Engine & Under Hood

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

C6OZ-8509-A For any S code 390 engine without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single sheave pulley, 6-3/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford part number C60E-8509-C.

C6AZ-8509-C 390 engines with air conditioning. Power steering and or thermactor emissions allowed. 2 sheaves with a diameter of about 5-5/16 inches. *Notes say after 1-9-1967 engine build date. Ford casting number C6AE-8509-F.

C6AZ-8509-D Strictly California 390 Cougars without air conditioning. With or without power steering. 3 sheave pulley with diameters of both 5-11/16 inches and 6-1/8 inches. Ford casting number C6AE-8509-J.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Double sheave pulley, 6-3/8 inches and 5-11/16 inches in diameter pulleys.Application:429CJ with air conditioning and/or power steering. Ford casting number D0OE-8509-L. Ford part number D0OZ-8509-L

Single sheave pulley, 6-1/2 inches in diameter.Application:429CJ without air conditioning and without power steering. Ford casting number D0SE-8509-A. Ford part number D0SZ-8509-A

Used FoMoCo 20 inch small block radiator. This is for a 1967 Mercury Cougar or Ford Mustang with 289-2V, or 289-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 7EC or 3rd week of May 1967. Late production date. Ford part number C7ZE-8005-S1 ...

Used FoMoCo 20 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 8FD or 4th week of June 1968. Very late production date.Replaces Ford part number C8ZE-8005-H1 ...

Used 'CORE" grade radiator, marked C9ZE-D or D1, .. etc. 20 inch used radiator from 1969 Mercury Cougar with Boss 302 or 351W or 1969 Ford Mustang with 302 or 351W or engines. This radiator will have the lower tank for transmission lines. Core grade, likely it has been recored at some point in the last 45 plus years. Limited to stock on hand.Restoring or re-coring OEM radiators is expensive and more for the concours crowd. New or reproduction radiators makes much more economical sense.Ford...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Used 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. Replaces Ford part number C8ZE-8005

Used WMo or Western Modine 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Dated 67 12. Replaces Ford part number C8ZE-8005

Used FoMoCo radiator marked C8ZE-L1 and dated 8KB, which we believe is 2nd week of October 1968. This is for an early built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and 4 speed transmissions. Good used radiator for recoring and restoration.Replaces Ford part number C8ZE-8005-L or C8ZZ-8005-C.

Correct core radiator for any 1970 Mercury Cougar or Ford Mustang with the G code Boss 302 engine. Has correct stamped Ford part number on the side strap, and lower tank without fittings for cooling lines. Core grade, will likely need recoring.Replaces Ford part number D0ZE-8005-E / E1

1970 Boss 302 radiator marked D0ZE-E1 and dated 9JD, we decipher the date as Sept 1969, 4th week. It has a 3 core construction as shown, with a rebuild tag. The upper and lower tanks and side brackets are all good. Fits any 1970 Boss 302 Mercury Cougar Eliminator and 1970 Boss 302 Mustang, it is dated for a October - November built car. Nice used assembly line, core radiator with original tanks. *Note - Does not have fittings for automatic transmission lines. All Boss 302 cars had 4 speed...

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion is about 24 inches long.  Replaces Ford part number D0OB-8B170-B.

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. Tube dimensions 5/16" O.D. x 1.560" long. C6AZ-9A484-B

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Specific to 1968 302-2V, and 302-4V all with manual transmissions - 3 speed or 4 speed. Same tube both sides, sold singly as a bare tube without installation hardware. Two total needed, one for use on each cylinder head. Must use cylinder heads with casting number C8OE-6090-L (302-2V) or C8OE-6090-K (302-4V).Pictured below are some shots of an unrestored J code 302 as taken from a low mile 4spd XR7 parts car. We thought we would post these pictures as a reference for those wanting to know what...

California emissions 351-2V air cleaner snorkel. DSO 52 and DSO 53 Cougars with H-code 351-2V engines.

This snorkel was found on the XR7-G model with a 390 or 428 engine with the tall pent roof finned aluminum valve covers. The HERTZ model with the 390 engine used a chrome "Powered By Ford" chrome valve cover and did not need the extra length in the extension. This is a refurbished snorkel made from original parts. Very high quality construction.Ford part # C8WY-9A626-B.

This one year only, 1969 S code 390-4V or 390IP (Improved performance). Same jog as the 428CJ snorkel. It is technically a 428CJ snorkel with the addition of an adapter on the heat riser opening reducing it down for use with a 2 inch I.D. paper "S" tube. Ford part number C9OZ-9A626-C.

Application would be for only 1971 Cougars with the 429CJ option, either ram air or non-ram air. Original Ford part number is D0GY-9A626-A.  Also used on the Torino / Cyclone / Cobra / Ranchero.  Notice the main difference between this genuine CJ snorkel and the "Economy" truck snorkel we have listed is the mounting flange hole placement and contour. Click on images to enlarge. ...

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs. Ford part number C9ZZ-9A626-C

This is a 1968 only part that is correct for Cougars equipped with the 390 GT "S" code motor. Whether your Cougar has the GT package or not, as long as it has a 4V 390 motor, this is the correct snorkel for your Cougar. The internal dimensions of the opening at the air cleaner base end measure 4 1/8" X 2 3/16", the flange mounting holes measure 5 1/2" on center. The opening for the S tube is 2 3/4". Please keep in mind that our hard to find parts like this are not always competitively priced...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Concours correct Autolite spark plug wires for any 1972-73 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Motorcraft', 'SIPCON', and the cylinder numbers individually imprinted on the 7mm wires. Orange spark plug boots on this set.

D3AZ-6758-B All steel tube that was used on 1973 H code 351-2V engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-2V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note - Excludes 1973 Q code 351CJ engines.

D3AZ-6758-C All steel tube that was used on 1973 Q code 351-4V or 351CJ engines, one end inserted into the rear of the carburetor vacuum fitting (had a rubber hose connecting them 6N664) and the other end inserted into the straight end of the D3-6A664-4V PCV hose. This is a formed tube with barbed ends, it does not use clamps. *Note – Excludes 1973 H code 351-2V engines.