All Available Parts - 1968 Mercury Cougar

Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...

This often times missing bracket was attached to the back of your early 1967 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the less common design.It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend into the rectangular hole to keep the bracket properly anchored to the fragile plastic. For some reason the majority of the cars built didn't get the better...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction burl woodgrain decal for the 1968 XR7G sunroof / fog light switch.

Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang.  Sold individually, 4 needed per car.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a big block engine. This item requires a $30 core charge.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely. Replaces item # 31907Through 67-68, there were four different style brackets, you can see all four...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction underhood A/C performance upgrade kit for the 1967 - 1968 Cougar equipped with the 289 or 302 engine.  This kit combines the compressor conversion kit with a Superkool condenser assembly, new barrier style A/C hoses and expansion valve to maximize the performance of the factory A/C system. Also includes a compressor safety switch to protect the new components from excessive high or low system pressures. Excellent choice for vehicles being retrofitted for newer automotive...

Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Reproduction set of idler arm bolts for the 1967 - 1968 Cougar or Mustang.

Chrome screw used to mount the rear interior panel keeper.Sold individually.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Used wiring pigtail that runs from the 14290 under hood harness to the driver side marker light on the 1968 Cougar. NOTE: Wire diagram shows brown and black leads. We've found that most cars have yellow and black. Please note colors you need in the comments section of your order.

Used wiring pigtail that runs from the under hood harness to the driver side headlight harness on the 67 - 68 Cougar.

Used wiring pigtail that runs from the under hood harness at the kick panel to the starter solenoid / horn / voltage regulator on the 67 - 68 Cougar.

Used 1968 Mercury Cougar sunroof motor access panel. This panel is covered by the headliner, but can be dropped down (headliner is glued to the panel) to access the sunroof motor. Will always have a multiple, repairable cracks, but is still functional.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction wiring pigtail repair kit for the sequential box on the 1968 Cougar.  Included are: 1 four pin red connector1 four pin black square connector1 four pin white square connector1 four pin flat connector 1 two pin connector

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction 15 x 7 gold haze colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim.  Cast...

Reproduction set of 20 lug nuts used specifically on the Rocket Racing wheels. These lugs will not work on any other wheel.

CURRENT ETA FOR THESE WHEELS IS 2/24/2023 Reproduction 17 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a gold background.  *NOTE - These caps are specifically designed to fit the LW10 series wheels.

Reproduction Cobra GT 350 center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic blue cobra with red detail.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...

This listing includes all parts shown here. It is correct for a 1967 Mustang but for those 1967 Cougar owners looking to delete the tired, warped, peeling old pads this is a great way to clean up a very focal part in your interior. These items can also replace the very hard to find 1968 console parts found in both the Mustang and Cougar but look much different than the 1968 style. Keep in mind West Coast Classic Cougar will take your Grade A 1967 or 1968 used console parts in trade. ...

Reproduction 6.5 litre (390) fender emblem for the Mercury Cougar. These were used on all XR7G models with an S or X code 390, on other Cougars they were used with the Cougars that came equipped with a 390, but without the GT option package. Unlike the originals these do not have mounting studs, but are firmly held in place with 3M VHT double sided emblem tape.

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

Used wiring pigtail that runs from the taillight harness ground wire to the K8 / K9 sequential motor. Will work on 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the driver side turn signal harness on the 67 - 68 Cougar Standard and XR7 models.

Used wiring pigtail that runs from the under hood harness pigtail to the driver side headlight harness (brown plug) on the 67 - 68 Standard or XR7 model Cougar.

Green floor mats for the 67 - 73 Cougar embroidered with the Cougar script logo.

Dark green floor mats for the 67 - 73 Cougar embroidered with the walking cat logo.

Used roll up door replacement slat. If you damage one you can remove the door, slide the damaged slat off the rubber backer and slide the replacement in. Sold individually.

Reproduction shifter boot for aftermarket shifters on 67 - 68 Cougars, or 64 - 68 Mustangs. Perfect fit for Hurst shifters and will accommodate other aftermarket shifters.   

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

Upholstery kit for covering the headrests on the 1968 Cougar. Does not include headrest hardware or foam.  Made from the same Sierra grain 32oz vinyl material as our upholstery kits. Sold as a pair.

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Dark Red / Maroon floor mats for the 67 - 73 Cougar embroidered with the XR7 logo.

Reproduction gold walking cat emblem / insert for the 1968 XR7G T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 68 XR7G, this handle will fit on any 67 - 73 Cougar with an automatic transmission.

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

Used wiring pigtail that runs from the under hood harness to the horn / voltage regulator / starter solenoid on the 67 - 68 Standard and XR7 model Cougars. Located above the driver side kick panel behind the heater controls. 

Used wiring pigtail that runs from the under hood harness to the voltage regulator ground bolt on the 67-68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the starter solenoid on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the ignition switch on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the alternator harness on the 67 - 68 Standard and XR7 model Cougars.

Used wiring harness that runs from the taillight harness to the emergency relay on the 67 - 68 Standard and XR7 model Cougars. 

Used wiring pigtail that runs from the under hood harness to the small post on the starter side of the starter relay on the 67 - 68 Standard and XR7 model Cougars. 

Used wiring pigtail that runs from the under hood harness to the voltage regulator from the alternator harness on the 67 - 68 Standard model Cougars.

There are three of these small rings on your cluster that outline the amp, temperature and fuel gauges. The oil pressure gauge is unique in that the decorative black ring is incorporated into the gauge housing.Sold individually, three per car.

There are two of these rings on the driver side cluster. One outlines the tachometer and one outlines the speedometer. Sold individually, two per car.

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

Used retaining bolt with nut for the fixed column on any 67 - 68 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

This listing is for the outer doors pieces only, Cougar and Mustang are identical. Sold only as a pair.Replaces Ford part numbers C7ZZ-6521453-A  and  C7ZZ-6521452-A

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

The car pictured is a 67, but the copyright says "1969 Fred Bonner Corporation" and the header says Mercury Cougar introduced 1968.Measures 5"x7"

NOS Rand McNally Lincoln Mercury atlas and travel guide, originally distributed to customers through their local dealer. Includes state, city and "special maps" that include the US, Central America, Mexico and Puerto Rico. Also includes a special features section with points of interest.

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

NOS C6 Automatic Transmission training handbook from the Ford Marketing Corporation. Course 7521, Vol. 71 S4-L2. Everything from the torque converter, to the planetary gear and hydraulic systems to diagnosis and adjustments are detailed in this manual. Everything about descriptions, testing procedures and specifications were approved by Ford. Filled with color photos and diagrams. There is an unknown name written on the inside of the cover, however all pages are intact and in perfect...

NOS 41" x 24" Walking Cat nylon banner / flag. These were hung up around dealers back in the sixties and early seventies. We're calling it a banner, but the 2 holes on one side of it indicates it may also be a flag.   NOTE* The reflectiveness of the nylon made it a bit difficult to photograph, just know that the banner is in fact white! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually...

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

Final issue / November 1975This manual was taken from the original box and each page was painstakingly placed in a Mylar sleeve. No damaged, missing pages or writing on pages. Anyone serious about buying and selling parts for a 1965 1966 1967 1968 1969 1970 1971 1972 Comet / Cyclone / Cougar / Mark III will find this all inclusive manual will quickly pay for itself. If you pick it up in person we can reduce the price significantly, we can store it for as long as you need until you can pack it...

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

NOS Ford service training manual on diagnosis of charging system problems. This booklet is a guide to diagnosis of the alternator, regulator, battery and wiring issues. It contains diagnostic procedures and self instructional tests and was meant to be used as a reference guide for the "charging system videotape (video tape not included).  16 pages long with tests and answers.Issued Dec. 1974, # 365-240

This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1968. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-68 Course 13003 and 1760Volume 68 S4

Motor Trend Magazine January 1968 issue featuring the 1968 Cougar, Mustang, Camaro, Barracuda, Javelin and Firebird. Condition is lightly used. List of topics in this issue are: Concept cars coming out of DetroitThe Charlotte national 500Classic cars of the 50'sLatest auto news from EuropeReturning to 1919 & Hispano-Stutz 37.2Racing cars = Barracuda 340 vs. Camaro 396 vs. Cougar 390 vs. Firebird 400 vs. Javelin 343 vs. Mustang 390All the usual fun and eye catching classic ads common in...

NOS Dinky Toys 1968 Mercury Cougar. Still in the box and in perfect condition. High quality production made by the Meccano factory in Liverpool, England, these toy are the real deal and not cheap plastic.   Features: Retractable antennaReal rubber tiresOpening doorsTilting front seatsSuspension

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

Rebuilt C4 24 spline torque converter for the 1967 - 68 Mercury Cougar or 1966 - 69 Ford Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. Ford part number C6AZ-7902-M. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of...

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

This kit is for the EARLY 1968 Cougar, we also list the LATE 1968 version. There are minor differences between the two. This basic kit will save you many hours on your grille restoration especially if you do not own a bead blasting cabinet or the specialty power tools needed to separate the chrome grille bars from the grille assembly. To come up with this "near perfect" group of parts we have to disassemble several West Coast, corrosion free grilles and inspect them very closely. Next we glass...

This kit is for the LATE 1968 Cougar, we also list the EARLY 1968 version. There are minor differences between the two. This basic kit will save you many hours on your grille restoration especially if you do not own a bead blasting cabinet or the specialty power tools needed to separate the chrome grille bars from the grille assembly. To come up with this "near perfect" group of parts we have to disassemble several West Coast, corrosion free grilles and inspect them very closely. Next we glass...

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

Used custom cut driver side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551701-B

Used custom cut passenger side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551700-B