Home > 1968 Mercury Cougar
All Available Parts - 1968 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 5410
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 11-0203 -
C7ZZ-222A55-A Door window rear stop, which installs to the guide (C7ZZ-65222A57). Stop adjusts the door glass in its up most position. One per door, fits left side. This piece falls down inside the door when the rear guide is removed. Bolt included, but may not be exactly as pictured.You can find the reproduction here. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...
Availability: Used / Wrecking Yard Item
Item #: 11-0205 -
C5ZZ-6521768-A Front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door.See C7ZZ-6521772-A for the rear stop bracket and bolt.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...
Availability: Used / Wrecking Yard Item
Item #: 11-0206 -
C7ZZ-6521772-A Bracket that mounts to the door window channel, it prevents the rear section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and Ford Mustangs. Works on either the passenger or drivers side door. Casting # is C7ZB-21772-A See C7ZZ-222A54-A for the companion stop on the door guide.See C7ZZ-6521768-A for the front stop bracket and bolt.You can find the reproduction here.Check out our handy diagram below to find other '67-'68 door parts you...
Availability: Used / Wrecking Yard Item
Item #: 11-0165 -
375694-S2 Special set screw for the rear door guide. This one is shorter than the two that install in the vent window frame and front door glass channel. This set screw has a 5/32" hex head with 5/16" NC threads, and is 1-9/16 inches in overall length. This set screw also has a ¾ inch diameter shoulder. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See...
Availability: Used / Wrecking Yard Item
Item #: 11-0166 -
378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...
Availability: Used / Wrecking Yard Item
Item #: 11-0177 -
C7ZZ-6523288-A Steel slider mounts to the door window channel. Your door window regulator's two arms slide in this channel lifting or lowering the door glass. Works on either the passenger or drivers side doors of a 1967-68 Mercury Cougar or Ford Mustang.*Installation tip - Channel needs to be void of all old grease. For a smooth operation, replace with fresh lubricant for years of trouble free service.Check out our handy diagram below to find other '67-'68 door parts you may need. All the...
Availability: Used / Wrecking Yard Item
Item #: 11-0170 -
C5AZ-6223230-A Steel bracket that mounts to the door of all 1967-68 Mercury Cougar and Ford Mustangs. This is the lower window regulator arm slider bracket. Comes with original mounting bolts. Works on either the passenger or drivers side door.*Installation tip - Channel needs to be void of all old grease. For a smooth operation, replace with fresh lubricant for years of trouble free service.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...
Availability: Used / Wrecking Yard Item
Item #: 11-0178 -
23318 This is the door window counterbalance spring that goes on the window regulator of a 1967-68 Mercury Cougar or Ford Mustang. Obsolete in the Master Parts Catalog
Availability: In-Stock Item
Item #: 19238 -
Very correct, quality regulator that is much better than the imports we see that are made of a softer metal. Replaces Ford Part # C8ZZ-6523201.*NOTE* The 1967 splined stud the window crank mounts to is taller on the 67 than the 68. They are not meant to interchange 67 to 68. If you install a 1967 regulator on your 1968 the window crank will not seat properly and will protrude from the door panel. If you try to install a 1968 regulator on a 1967 model the window crank will fit too tight to the...
Availability: In-Stock Item
Item #: 19283 -
Very correct, quality regulator that is much better than the imports we see that are made of a softer metal. Replaces Ford Part # C8ZZ-6523201.*NOTE* The 1967 splined stud the window crank mounts to is taller on the 67 than the 68. They are not meant to interchange 67 to 68. If you install a 1967 regulator on your 1968 the window crank will not seat properly and will protrude from the door panel. If you try to install a 1968 regulator on a 1967 model the window crank will fit too tight to the...
Availability: In-Stock Item
Item #: 13133 -
C7ZZ-652221-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind.*Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0239 -
C7ZZ-6521458-B Bare channel for mounting the right side or passenger door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Can also be found with part number C7ZZ-6521458-C. Regulator slide not included, see related items for the slides. Those are in short supply. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on...
Availability: Used / Wrecking Yard Item
Item #: 11-0249 -
C7ZZ-6521459-B Bare channel for mounting the left side or driver door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Regulator slide not included, see related items for the slides. Those are in short supply. Can also be found with part number C7ZZ-6521459-C. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search...
Availability: Used / Wrecking Yard Item
Item #: 11-0237 -
C7ZZ-652220-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind.*Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0248 -
C7ZZ-652221-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind.*Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0425 -
Special bolt with large square captured washer. This one is shorter of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 7/8" of threads with a dog point. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 379384-S2.
Availability: Out of Stock
Item #: 11-0426 -
Special bolt with large square captured washer. This one is longer of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 1-7/8" of threads with a dog point. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 378694-S.
Availability: Used / Wrecking Yard Item
Item #: 11-0427 -
Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 33797-S.
Availability: In-Stock Item
Item #: 31207 -
Reproduction front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door.Replaces Ford part number C5ZZ-6521768-ACheck out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: In-Stock Item
Item #: 31325 -
Reproduction C7ZZ-222A54-A Door window rear stop, which installs to the guide (C7ZZ-65222A56/7). Stop adjusts the door glass in its up most position. One per door, fits right side. This piece falls down inside the door when the rear guide is removed. Bolt included. Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: Window Regulator Replacement - 1967-68 Cougar / Mustang Check out our handy diagram below to find other '67-'68 door parts...
Availability: In-Stock Item
Item #: 31326 -
Reproduction C7ZZ-222A55-A Door window rear stop, which installs to the guide (C7ZZ-65222A57). Stop adjusts the door glass in its up most position. One per door, fits left side. This piece falls down inside the door when the rear guide is removed. Bolt included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: In-Stock Item
Item #: 31327 -
Reproduction C7ZZ-6521772-A Bracket that mounts to the door window channel, it prevents the rear section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and Ford Mustangs. Works on either the passenger or driver side door. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18891 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18892 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great, look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18893 -
Upholstery components have an ETA of 5 - 9 weeks.
We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials. Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18894 -
Upholstery components have an ETA of 5 - 9 weeks. We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials. *NOTE* This product will take 4 – 6 weeks for delivery.
Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18895 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great, look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18896 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 11801 -
These are great for your back seat belts or convertibles that did not use retractors in the front. They are an exact copy of the originals that were available as a dealer option from 1964 and up. Sold Individually. Made in U.S.A. Replaces Ford Part #: C4AZ-65611A06. Customer feedback: I just wanted to tell that your delivery has arrived today. Thanks a lot! Never ever ordered something (not even here in Germany) and got it that fast. Awesome! My next orders will go to your place and I will...
Availability: In-Stock Item
Item #: 41825 -
Includes one lap belt, the mounting bolts and washers.sold individually
Availability: In-Stock Item
Item #: 41826 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually
Availability: In-Stock Item
Item #: 41828 -
Great looking replacement style seat belt. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. These are great lap belts for convertible cars that don't use retractors. We suggest using seat belt anchor bolts for an easy installation of these aftermarket lap seat belts. This kit does come with installation hardware, but the threads on the bolt are coarse, and will not bolt into your original threaded anchor points. sold individually ...
Availability: In-Stock Item
Item #: 41895 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually
Availability: In-Stock Item
Item #: 41833 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41829 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41822 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41823 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41832 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 13711 -
These are era-correct looking seat belts at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers
Availability: Used / Wrecking Yard Item
Item #: 14-1011 -
Both deluxe and standard used the same retractor in 1968 - 1969 and left is the same design as right. Grade "B" retractors will be 100% functional but cosmetically will show a crack in the plastic holster, and may have minor rust on chrome. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-1014 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.
Availability: Used / Wrecking Yard Item
Item #: 14-1012 -
Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-0000 -
This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...
Availability: Used / Wrecking Yard Item
Item #: 14-0100 -
This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...
Availability: Used / Wrecking Yard Item
Item #: 14-0110 -
Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...
Availability: Used / Wrecking Yard Item
Item #: 14-5001 -
This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...
Availability: Used / Wrecking Yard Item
Item #: 14-0073 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.
Availability: Used / Wrecking Yard Item
Item #: 14-0063 -
Hard to find without being faded, frayed or rusted buckle. Rarely, if ever will our used shoulder belts look this pristine as they are prone to sun fade. Sold individually, 2 required per car, hardware sold separate. Contact us for colors other than black. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-0021 -
When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...
Availability: In-Stock Item
Item #: 30177 -
Complete set of front seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts, 4 large washers, 2 spacers and 4 rubber anti-rattle gaskets. Get the rear set here.
Availability: In-Stock Item
Item #: 30180 -
Complete set of rear seat belt bolts for your 67 - 68 Cougar or Mustang. Included are the 4 bolts and 4 spacers. Get the front set here.
Availability: In-Stock Item
Item #: 30858 -
Premium quality deluxe shoulder and lap belt with re-tractor. Deluxe belts with chrome bezels were equipped on many 68 - 69 Cougars and Mustangs. If you prefer the standard version with a black band on the buckle, just mention it and we will change it out at no extra cost. Many of our customers are calling this a "concours" set, but they do not qualify for that. If you look close you will see the nylon webbing has four bands which is correct for 1968. 1969 and up used a three band pattern on...
Availability: In-Stock Item
Item #: 30884 -
These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...
Availability: In-Stock Item
Item #: 30898 -
Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...
Availability: Used / Wrecking Yard Item
Item #: 14-1035 -
This is a 100% complete, functional set taken from multiple 1968 Mercury Cougars. Often it takes 2-3 cars to put together one set, decent driver quality set as the driver side will often show excessive wear and other belts can be rusted or missing. The set has been thoroughly inspected, cleaned and redyed with RIT dye in a boiling vat with vinegar. This set is driver quality and if one looks closely you will probably find a small crack in each of the re-tractor plastic covers, a few dots of...
Availability: Used / Wrecking Yard Item
Item #: 14-1034 -
This is a 100% complete, functional set taken from multiple 1967 Mercury Cougars. Often it takes 2-3 cars to put together one set, decent driver quality set as the driver side will often show excessive wear and other belts can be rusted or missing. The set has been thoroughly inspected, cleaned and redyed with RIT dye in a boiling vat with vinegar. This set is driver quality and if one looks closely you will probably find a small crack in each of the re-tractor plastic covers, a few dots of...
Availability: In-Stock Item
Item #: 31000 -
Premium quality deluxe rear lap belt. Deluxe belts with chrome bezels were equipped on many 68 - 69 Cougars and Mustangs. If you prefer the standard version with a black band on the buckle, just mention it and we will change it out at no extra cost. Many of our customers are calling this a "concours" set, but they do not qualify for that. If you look close you will see the nylon webbing has four bands which is correct for 1968. 1969 and up used a three band pattern on the webbing. Notice it...
Availability: In-Stock Item
Item #: 13708 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13706 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13710 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13715 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: In-Stock Item
Item #: 13714 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13712 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually
Availability: In-Stock Item
Item #: 13707 -
This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY
Availability: In-Stock Item
Item #: 13709 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: In-Stock Item
Item #: 31017 -
Reproduction set of Deluxe seat belts for the 68 - 69 Cougar or Mustang Coupe. Some things you may want to notice are that although these are made to fit both 68 and 69, the webbing is the 68 style. 1968 belts had four rows of material that make up the belt and 1969 belts had three rows (as seen in the picture above). Also, the rear belts will not have the plastic sheaths that keep the belts from falling in between the seats. These belts are premium quality and come complete with deluxe...
Availability: In-Stock Item
Item #: 14-1037 -
Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above. Sold individually, one per buckle.
Availability: In-Stock Item
Item #: 32360 -
Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A
Availability: In-Stock Item
Item #: 14062 -
A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...
Availability: In-Stock Item
Item #: 26760 -
These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!
Availability: Used / Wrecking Yard Item
Item #: 20531 -
Very rare over the counter, Group II dress up accessory item for any 289 / 302 small block engine. In excellent used condition with no cracks, stripped threads or corrosion damage. The nicest you will ever find. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. This intake is basically the same one you so often see with COBRA lettering on it. New to our inventory as of 12-15-2017, the...
Availability: Ships Direct from Supplier (Except International)
Item #: 26084 -
Reproduction Polished Stainless Steel Engine Compartment Dress Up Kit for the 1967 and 1968 Mercury Cougar
Click on images to enlarge. Installation Instructions You will need a few tools to install your kit. A Standard socket set and wrenches, a
set of standard alien wrenches, a utility knife, anti - seize compound, a electric
drill, a new sharp 9/32 drill bit, rubber tipped clamps, lacquer thinner, window
cleaner, black permanent pen and soft clean cotton baby diaper for cleaning your kit....
Availability: In-Stock Item
Item #: 11337 -
Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.
Availability: In-Stock Item
Item #: 11338 -
Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.
Availability: Ships Direct from Supplier (Except International)
Item #: 20047 -
Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...
Availability: In-Stock Item
Item #: 42020 -
This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...
Availability: In-Stock Item
Item #: 14-1001 -
Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent.
Availability: In-Stock Item
Item #: 30713 -
Reproduction 15 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...
Availability: In-Stock Item
Item #: 30727 -
Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...
Availability: In-Stock Item
Item #: 30791 -
One of the most common problems with first-generation Cougars is droopy hidden headlight eyelids, which make the otherwise iconic front grille look like an eyesore. This inexpensive and easy to install kit provides stops for the eyelids to rest against in the closed position. It also provides some extra structural support to take some of the pressure off the built in bump stops. The vacuum actuators on these cars create extreme downward pressure at all times when running, causing the upper...
Availability: In-Stock Item
Item #: 30842 -
Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.
Availability: In-Stock Item
Item #: 31146 -
This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...
Availability: In-Stock Item
Item #: 31615 -
This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.
Availability: In-Stock Item
Item #: 31616 -
This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.
Availability: In-Stock Item
Item #: 31623 -
This listing is for the outer wheel house upper patch for the driver side of your 67-68.
Availability: In-Stock Item
Item #: 31624 -
This listing is for the outer upper wheel house patch for the passenger side of your 67-68.
Availability: Used / Wrecking Yard Item
Item #: 31639 -
Used passenger side seat back release catch for the 68 - 70 Cougar or Mustang.
Spotlight!
Featured!
Availability: Ships Direct from Supplier (Except International)
Item #: 31648 -
Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid. Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...
Availability: In-Stock Item
Item #: 31655 -
Reproduction upper tube lower insulator for the 1968 Cougar or Mustang column. Used to stabilize the lower end of the steering column. Works on both tilt and fixed columns. Outside diameter is 2-1/8" inches and inside diameter is 1-1/2" inches. NOTE* Ford describes this as an "upper" bearing in relation to the lower steering column tube bearing. It is not used at the upper end of the column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31683 -
Reproduction taillight panel for the 67-68 Cougar. Yet another in a long line of great fitting parts from our friends over at Dynacorn, this replacement taillight panel is perfect for those of you who have rust holes in and around the taillight area. As seen in the photo above, this is only the taillight panel and will not include the quarter extension panels or the rear taillight lower structure. ...
Availability: In-Stock Item
Item #: 31694 -
Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background. *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...
Availability: In-Stock Item
Item #: 31695 -
Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang. Dimensions: 9/16" - 18.
Availability: Ships Direct from Supplier (Except International)
Item #: 31712 -
Reproduction cowl panel for the 67 - 68 Mercury Cougar. This is the upper portion visible from the top of the car. This panel is unique to Cougar as it does not have the crown in the middle like the Mustang cowl panel has.NOTE! Dynacorn is currently welding the two halves together in house. This makes them almost impossible to install. We have talked to them about just sending the two halves apart and thought they were on board but alas these are still being spot welded together and...
Availability: In-Stock Item
Item #: 31718 -
Reproduction grommet that seals the check valve to the Midland brake booster on the 67 - 68 Cougar or Mustang. We also sell the grommet / check valve combo, you can find it here.
Availability: In-Stock Item
Item #: 31734 -
Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.
Availability: In-Stock Item
Item #: 31735 -
Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31871 -
Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California. Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31872 -
Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California. Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31873 -
Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon. Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.
Availability: Used / Wrecking Yard Item
Item #: 31887 -
Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...