All Available Parts - 1970 Mercury Cougar

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used center vent connector or duct tube. Fits 1969-70 Mercury Cougar with factory or integral air conditioning. This attaches to the center register in the dash pad. Replaces Ford part number C9WA-19B737-A or C, and C9WY-19B680-B.*Note - Will not fit Ford Mustang.

Used passenger side connector duct tube or elbow, attaches to passenger side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C626-C

Used driver side connector duct tube or elbow, attaches to driver side air conditioning register. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19B680-D and C9ZA-19C850-A.

Used driver side flex connector duct tube, middle of three duct tubes on driver side. This tube has a stapled flex hose included. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZZ-19C692-B and C9ZA-19C615-F.

Used driver side connector duct tube, attaches to driver side air conditioning register. Fits center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B923-B, C9ZA-19B923-A, or C9ZZ-19B680-C.

Used passengerer side connector duct tube, attaches to passenger side air conditioning register. Fits to center assembly. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. Replaces Ford part number C9ZA-19B737-C or C9ZZ-19B680-B.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number C9ZZ-18471-A.

Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

Complete heater and air conditioning control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic chrome knobs and lever borders. Does not include the indicator light plug and harness. Knobs, if included may not be in the greatest shape. We suggest purchasing the new reproduction knobs. Ford part # C9ZZ-19A884-A. *Restoration Tip* For...

This is a used A/C center vent attaching clip. Two required per center AC vent, the two tiny tabs fit in the holes on the sides of the vent assembly and when you tighten the Phillips screw it will pull the vent tight against the dash pad. Very hard to come by, others have used silicone to bond the chrome vent in place when clips could not be found.Replaces Ford part number C7AZ-14570-A.

Complete vent includes mounting hardware. These are sold individually, so please choose between passenger and driver side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-C passenger side, C9ZZ-19893-D driver side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Used fresh air vent found in the passenger side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501934-A.

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.

Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Exact replacement to original dryer. Drier removes moisture and should be changed anytime system is recharged. It is the life of your system. Stainless steel filter element. Filter stops contaminants from clogging expansion valve. Replaces part # C9ZZ-19959-A.

Our new high performance condenser kit comes pre-assembled with the drier and all brackets. 1967 - 1968 condenser shown. These condensers are one of the highest performing, durable condensers available in today's automotive market. This condenser was designed specifically to increase heat transfer for lower head pressures during idle situations, allowing more airflow to pass through the condenser and give the radiator enough airflow to operate properly. Remember to remove your coupler...

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

Regardless of which V-8 engine, C9ZA-19972-C or C9ZA-19972-E, both are the correct part number. This hose is approximately 20 inches long. Ford part # C9ZZ-19972-C.

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

A/C suction line for the evaporator to compressor for the 1970 Mercury Cougar or Ford Mustang with any V-8 engine. This hose is approximately 55 inches long.Ford part # D0ZA-19867-A and MPC # D0ZZ-19867-A.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch 'O'-ring fitting for discharge hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Very hard to come by in perfect condition with no cracks. Both coupe and convertible use the same piece.

This plastic part will have a minor crack at the top. Add desired color into the comments section.

This part will have a crack, usually at the top. Convertible and coupe used the same plastic trim. Add your desired color in the comments section.

Whenever possible we include broken off tabs on our grade B rear panels. Keep in mind the panel pictured will not be the panel you receive but rather a like item.

Used Convertible Driver Rear Interior Panel Grade "B" for the 1969 and 1970 Mercury Cougar

Rarely will you find perfect vinyl on a rear convertible panel. Our grade "A" rating refers to the condition of the plastic backing, not the vinyl.

Used Convertible Driver Rear Interior Panel Grade "A" for the 1969 and 170 Mercury Cougar

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

Metal portion of the passenger side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust. Basic Ford part number is 7631004.  *Note - Excludes Late 1970 with larger power window bezels.

Metal portion of the driver side rear interior panel on a 1969-70 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Grade A used, no obvious dents or rust.Basic Ford part number is 7631005. 

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original! Several known versions of this valve at least two shown in photos.Fits 1969-70 Mercury Cougar and Mustang, 1968-69 Lincoln Continental.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C8VY-19849-A. aka YG-28

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Metal portion of the driver side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at least...

Metal portion of the passenger side rear interior panel on a LATE 1970 Mercury Cougar convertible, all with power windows. Power windows were an option on Cougars starting in 1969. This is the metal textured section only, does not include the "L" shaped padded section with arm rest. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels. Grade B used, will have at...

This new single texture two ply denim convertible top is an inexpensive top that is only recommended if you car is going to be stored indoors.*NOTE* This is the convertible top only. Top bows, tack strips, and tension cables are NOT included with this item.Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our installation video below! ...

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. It is often referred to as an OEM replacement, but that is not exactly accurate...This is a two-ply composite...

Hard plastic terminal covers for the alternator. Replaces Ford Part #c7zz-14056-A

Good used 10 blade alternator fan.Ford Part #: DOAZ-10A310-B.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Nice reproduction of the original alternator wiring harness, 3 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1970 Mercury Cougar standard models or 1970 Ford Mustang with factory tachometer option, all with 351/428CJ engines. Ford service number D0WY-14305-C.

Nice reproduction of the original alternator wiring harness, 2 pin dog bone style connector and wire colors match up to the original Ford drawings. Application is 1970 Mercury Cougar XR7 and Eliminator models or 1970 Ford Mustang without factory tachometer option, all with Boss 302/351/428CJ engines. Ford service number D0ZZ-14305-C. *Caution, not for use with Cougar standard models or Mustang with alternator warning light

Used clip found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

New replacement mounting clip as found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 351W or 351C engines. Sometimes has Ford number D0AA-8A617-A stamped on the bracket, not always.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in 1968, now have an ever so slight amount of play....

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

For 1968 390-2V engines without air conditioning, with dual alternator belts, and with power steering. 1968-69 390-4V, 427 GT-E, or 1968-69-70 428 Cobra Jet engines. All without air conditioning. All with dual alternator belts, and with power steering. Triple sheave 1968-69-70 crank pulley.Ford part # C8AZ-6A312-D, Ford casting # C8AE-6312-D.

D0OE-6312-A For both Windsor and Cleveland 351 engines starting in 1970. This is a single sheave pulley, meaning without air conditioning and without power steering. One groove with a diameter of 6-11/16 inches in diameter. Ford Master Part number D0OZ-6A312-A. A four bolt hole crankshaft pulley for use with 1970 and upward crank dampeners.

Has casting number D0OE-6312-B stamped on the inside. Application for 1970 all 351 engines, 1971 M code 351-4V, and 1971 and 1972 H code 351-2V engines with power steering or idler pulley. Dual sheave crankshaft pulley measurement of 8.00" and 6-11/16" diameters. No air conditioning. Ford Master Part number D0OZ-6A312-E. Four bolts hold it on too.

D0AE-6312-C For both the Cleveland and Windsor variety. Starting in 1970 Ford tried to standardize many of the engine parts. This is the "with air conditioning" pulley for all 1970 - 1971 351-2V & 351C-4V engines, and all 1972 -1973 351-2V engines. Triple sheave 6-23/32", 8.00", 8-13/32" inch diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0AZ-6A312-C. *Excludes 1972 and 1973 Q code 351CJ engines. This means all 1972 and...

C9OZ-6A312-F. Application 1969 and 1970 428CJ all with air conditioning, power steering optional. Ford casting number C9OE-6312-D. Triple sheave 69 70 428 CJ crank pulley.

Used crank shaft pulley for any 1970 Mercury Cougar or Ford Mustang with Boss 302 engine. This is a double groove pulley with a 5-13/16 inch inner pulley diameter, pulley turns the water pump and alternator. 6-5/8 inches diameter for the smog pump belt. This pulley would have been used without power steering. Also used only up until about Jan, 1970. After Jan 1970, Ford just installed a 3 sheave pulley with the middle sheave not being used. Replaces Ford part number D0ZE-6312-A. ...

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. 2 sheaves with a diameter of 5-7/8 inches. This is a good copy of the original water pump pulley, it has no stamped part number.Replaces   C6AZ-8509-A or C6AE-8509-A.

C8AZ-8509-D 1969 428 Super Cobra Jet only (V and W code axles), 1970 428CJ and 428SCJ prior to Sept 1, 1969. No air conditioning, power steering permissible. Three sheave pulley, 6-1/8 inches and 7-1/8 inches in diameter pulleys. Ford casting number C8AE-8509-C was originally imprinted in ink, if you look closely between the two bonded together pulleys that make this pulley up you may be able to read the C8AE-8509-A stamped casting number from the two sheave inner pulley.

Single sheave pulley 6-61/64 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number C9OE-8509-G.  Ford part number C9OZ-8509-D Note:  * The Master Parts...

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

Fits the 1969 Eliminator and all 1970 Cougar models. Fits all 1969 - 1970 Mustangs with high back seats.

Used on 1969 Mustang Mach I and Eliminator and all 1970 Mustangs and Cougars. American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process. Upper and lower cushion for one seat. Click on images to enlarge. ...

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Comes with everything shown to replace tracks on one seat, good quality reproduction made in China. Make sure and check out our good used originals if correctness is important to you.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This is the upper pressure hose, or the pump end only. Lower pressure hose Replaces Ford Part # : D0OZ-3A719-C

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.