All Available Parts - 1972 Ford Mustang

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes.This unit features a shorter arm than power brake pedals and is for use with a clutch pedal. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # D1ZZ-2455-D.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and a manual transmission. Not for cars produced after 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D1ZZ-6501508-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Here is a piece that will allow to install a modern DIN radio / CD player into your Mercury Cougar or Ford Mustang. No hacking or cutting required! *TRIVIA* Here's some alphabet soup for you. DIN stands for Duetch Industri Normen. An abbreviation for a standard in-dash radio measurement which is approximately 2 inches by 7 inches. The Germans starting using it to standardize the radio�??s in Audi�??s, BMW�??s, Mercedes, and VW�??s way back in the mid 80�?�s. ...

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford part # D2ZA-19A242. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Used in conjunction with the front bracket, bolts onto stud protruding from the rear of your radio, rather hard to find once the original radio has been removed. One exception; 1972-73 Mercury Cougar and Ford Mustang AM/FM radios used a different bracket marked D2ZA-18888-AB. *Customer Feedback*"These guys have got to be the most professional I've dealt with in the 4 years I've been restoring my Mustang and Cougar. I have had nothing but pleasant conversations even though I tend to be long...

Mercury Cougar and Ford Mustang factory AM/FM stereo. Good used working stereo, but the knobs are sold separately. Ford part # D2ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Chrome air cleaner lid removed from a Q code, 351-4V or 351CJ 1972 Mercury Cougar or Ford Mustang, likely Torino and Mercury mid sized cars too. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. Chrome will be used, and will have some defects to the plating.

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is the correct base for a 1972 Mercury Cougar with a Q code 351-4V Cleveland engine. It came with a painted lid unless your car happened to have been ordered with the "Sporty Exhaust" package and then a chrome lid was included. One year only air cleaner for the Cougar. Ford casting number D2ZF-9600-EA or D2ZF-9600-KA.

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Nice unused space saver spare tire for a Ford. Vintage Good Year brand tire with size F78-14. BF Goodrich is another common brand of tire installed for use with unique storage location, hold down, and inflation bottle. This one does not appear to have been inflated or used on the road. Still has the nubs on the face of the tire as shown.

Original space saver tire marked F78-15 from a 1970's Mercury or Ford. GoodYear brand it has the larger hub size, bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is period correct for a Goodyear tire, but typically B.F. Goodrich was optional on 1968-69 Cougar or Mustang. *NOTE* Does not include...

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

1971 - 1973 Convertible spare tire mounting, J bolt. MPC lists the total length as 9-1/2 inches long, and 5 inches threaded. Application is for hubcap type wheels only, those of you fortunate to have the style steel wheels need C8OZ-1448-A above.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

This is a the economy version of our lower control arm assembly, with a spot welded on reinforcing plate. We are sorry, but we just cannot recommend this part. The Scott Drake premium version of this lower control arm is superior and costs less. In the picture, you can tell that it is lacking a rolled lip on the outer edge that the originals and the Drake Premium reproduction offers. This is a non-returnable item. Having issues with wobbly or loose steering? Check out our video on sloppy...

Used driver side drum brake spindle for 1971-73 Mercury Cougar and Ford Mustang, as well as those mid sized Ford and Mercury's. Ford casting number D1OA-3108-AA.

Driver side disc brake spindle for 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1OZ-3106-A left hand or drivers side disc brake spindle. Guaranteed to be a flawless used part. Ford casting number D1ZA-3107-AA.

Reproduction passenger side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69.  Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here.All front end kit parts are identical for both power and manual steering.Note: Bright orange protective covers are to be removed before...

This is the 'variable ratio' power steering box, Saginaw manufactured. The Variable Ratio steering box was part of the Competition Suspension Package available optionally on all Cougars or part of the GT or 351CJ Performance Group. This Variable Ratio steering box should have come standard with all 1971 - 1973 M or Q code 351-4V or C or J code 429-CJ equipped Cougars. Sometimes this tag number could also be SPA-V. We offer used boxes because in our experiences this box design is very...

Good used passenger side (right hand) brake spindle for the Mercury Cougar or Ford Mustang equipped with front drum brakes. These are clean with no major rust and will also work on other mid sized Ford and Mercury products. Ford part # D1OA-3107-AA.

Passenger side disc brake spindle for 1971-73 Mercury Cougar and Ford Mustang. Ford part number D1OZ-3105-A right hand or passenger side disc brake spindle. Ford part number D1OZ-3106-A left hand or drivers side disc brake spindle. Guaranteed to be a flawless used part. Ford casting number D1ZA-3107-AA.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

Idler Arm Assembly for 1971-1973 Cougar and Mustang. Fits all 1971-1973 Cougars and Mustangs with manual or power steering. Complete with bushings installed and ready to bolt on. Does not include Zerk fitting. This Idler arm helps stop that floating feeling going down the road. Please see the installation photos below. Easy to install. 

Fits all 1971-73 Mercury Cougar and Ford Mustang with factory power or manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts.  Original Ford part number D1ZA-3355-A. Anghel Restorations...

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Grade A used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and D3ZZ-6560762. We also...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade A will not be chalky or have major scuffs or scratches. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and D3ZZ-6560763. We also have B...

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket...

This desirable option was used only on the driver side seat of the LATE 71-73 Cougar and Mustang. This is for seats that have the seat release knobs on the outsides of the seats. The early 71's had the release in the center of the seat. It can be installed on the passenger side with no modification other than extending the wiring that runs under the carpet.  Before we send out a system it will have been tested and will work in all positions and will not show excessive wear or...

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This passenger side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503598 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603598. *NOTE* Excludes Mustang Fastback and Mach 1 models. ...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Cast iron intake manifold used on all 1972 Q code 351-4V or 351CJ engines in a Mercury Cougar or 1971-72 Ford Mustang. Stock 4 barrel spread bore intake manifold. Take off manifold with correct casting number of D1ZE-9425-BB . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1ZE-9425-BB. *Note - 351 Cleveland engines only.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1972-73 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Motorcraft', 'SIPCON', and the cylinder numbers individually imprinted on the 7mm wires. Orange spark plug boots on this set.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-EA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-HA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-HB.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-FA.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for 97 and 631 bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these. ...

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2ZF-12127-CA.

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2AF-12127-KA.

Good used original distributor for the 351 Cleveland with a 2 barrel carburetor. Ford Part # D2ZF-12127-AA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-GA.

Good used original distributor for the 351 Cobra Jet. Ford Part # D2ZF-12127-GB.

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction battery powered  (AA battery) scratch built clock. Great alternative for those without a core for rebuild. American made reproduction console clock. Adjustment to clock is made from the reverse side of the clock, there is no stem through the lens for adjustment. Illumination of the dial is through the factory harness. Includes new lens and battery. No Core Required! Quartz movement clocks have second hands that click around, original clocks had a constant sweep...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory Q code 351CJ-4V V-8 engine. 351 Cleveland engine rated at 266 Hp with 8.0:1 compression ratio in 1972. 4 Bolt main caps on these engine blocks. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories,...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351C 1971-73 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have D0AE, D2AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 2C7 or March 7, 1972. D2AE-6015-CA.This item...

1971 - 1973 Mercury Cougar Ford Mustang rectangular clock found optionally in the center console. Used clocks generally do not work after 36 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks.Ford Part Number: D1ZZ-15000-C. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered...

Good Used Clock Harness for the 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Mach 1. Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness, and ashtray light socket and shroud. The Mustang wiring harness for the clock generally does not include the light socket for the ashtray. The MPC indicates that the Mach 1 did receive this Cougar wiring harness. Ford part number: D1WY-15A006-A and D1WB-15A006-A.

Used battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Used condition, minor pitting as shown. Replaces Ford Part #: D0OZ-10732-B.

This is the 100% correct Ford original battery hold down clamp. Stamped with D0OB10755A. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

Mint condition part that is almost always missing on cars equipped with group 27 battery. Great addition to your 1970 BOSS 302 Eliminator. Also correct for Mustang and Torino. Ford part # D0OZ-10A682-A, casting number as seen on part is D0OB-10A682-A. There is currently no correct reproduction of this part. Click here for more information on this rare part.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.