All Available Parts - 1969 Ford Mustang

This short harness attaches to the black power wire coming from the starter solenoid and then attaches to the harness that brings the power back to the convertible top pump or power sunroof motor. This harness is for the 1969 XR7 or 1969 Standard and the 1970 Standard but it is not correct for the 1970 XR7 with power sunroof or convertible top as the 1970 XR7 used a rocker switch mounted in the dash pad located above the AC or AC block off plate. *NOTE* Side by side comparisons between 1969...

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

This used header will be as good as you can get and it can be restored with some TLC. The part you get will be solid with minimal or no corrosion. Ford casting number C9ZB-76514A72-A

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Used condition pin and bushings for the 69 - 70 Convertible Cougar or Mustang.

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

Used driver side (left hand) and passenger side (right hand) convertible top boot moulding / trim for the standard Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Ford part # C9ZB-76423A19-A driver side, C9ZB-76423A18-A passenger side. *NOTE* If you have questions about your cores, checkout our video below. ...

Restored exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Restored exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This short section of wiring attaches to the terminal post on the starter solenoid that faces towards the firewall. The other end is a female plug that incorporates a fusible link. If your switch were to get stuck or the frame got in a bind with continued power being applied this is the portion that would blow saving you from a costly wiring "melt-down". This same part was used on both XR7 and standard Cougars with a power sunroof or convertible top.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford casting number C9ZB-76514A72-A

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603598-A, stamped with C9ZB-7603598-AW-R.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...

Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603599-A, stamped with C9ZB-7603599-AW-L.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...

Good used metal strip that fastens the weatherstrip to the bottom side of the header bow. Keep in mind we have (almost) every single used part related to the 69-73 Convertible Cougar and convertible Ford Mustang / Shelby in stock at all times.

This is the trim piece the goes across the top on the inside of the windshield. This piece will need to be sand blasted and repainted. Many people have chromed these, but from the factory they were painted satin silver.Ford Part #: C9ZZ-7603606-B

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

This two piece heat shield has a very narrow application in that it is a one year only item and only for the 390 IP (Improved Performance). It does not mate to metal a "S" shaped heat riser tube but rather a flexible paper-foil tube that attaches to a reducer on the bottom side of the snorkel. Very hard to find item, harder yet to find one that has not rusted out. The unit shown is "tender" in a couple of spots. The lower section carries a Ford part number of C9OZ-9A603-D and the upper section...

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

This one year only, 1969 S code 390-4V or 390IP (Improved performance). Same jog as the 428CJ snorkel. It is technically a 428CJ snorkel with the addition of an adapter on the heat riser opening reducing it down for use with a 2 inch I.D. paper "S" tube. Ford part number C9OZ-9A626-C.

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs. Ford part number C9ZZ-9A626-C

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

Fits all V8s with oval air cleaner.

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

Reproduction 15x6" styled steel wheel for your Mercury Cougar. This unit comes with 4.5" back-space, unless ordered otherwise. Hub caps and lug nuts are sold separately. NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not have the right attachment. If you attempt to balance these wheels without the correct adapter they will resemble a bent...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch and wiper switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Silicone and fasteners, everything needed for installation of our seat divider panel.

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Much better fit than the reproductions which make closing your door very difficult for the first year.Ford part # C9ZZ-7602627-A

Much better fit than our reproductions which make closing your door very difficult for the first year. Ford part # C9ZZ-7602626-A

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

NOS weatherstrip for the driver side (left hand) quarter window in the Mercury Cougar or Ford Mustang. Ford part # C9ZZ-65214A15-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

New Old Stock, technically a 'newer', NOS or service replacement driver side lower door hinge for 1969-70 Mercury Cougar or Ford Mustang. This version has the pin flattened out like a rivet as shown. Also this one has a slightly wallered out hole for mounting to the door.

New Old Stock NOS passenger side front turn signal assembly. Bezel, lens, housing. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering gear box. NOS in the box Ford part number C7ZZ-3524-C. ...

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

New old stock ashtray for any 1969-70 Mercury Cougar or Ford Mustang with factory console. This is the rear ash tray. Ford part number C8AZ-6262876-A.

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.

New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Timing chain set for your 67 - 72 Cougar or Mustang equipped with the 302 Engine.Gears (sprockets) are made from high alloy steel, and heat-treated for durability. Chain is pre-stressed and heat-treated for longevity.

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

C9OZ-7400-AAssembly 4 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. Check out our video on rebuilding your shifter below: ...

3 Speed manual transmission shift control assembly for any 1969 Cougar or Mustang. Control assembly only, no rods or chrome lever. C9OZ-7400-B Check out our video on rebuilding your shifter below: ...

C9OZ-7400-B3Assembly Factory 3 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our video on rebuilding your shifter below: ...

Used 4 speed manual transmission shift control assembly for the Mercury Cougar or Ford Mustang.Ford part # C9OZ-7400-A. Check out our video on rebuilding your shifter below: ...

Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.

C9ZZ-7210-A Shift lever for all 1969 Mercury Cougar and Ford Mustangs. Manual 3 speed only, 4 speeds are different. *Note - Must be used with Trunion C9OZ-7210-B, sold separately. Check out our video on rebuilding your shifter below: ...

C9OZ-7210-B "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 3 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 3 speed shift lever C9ZZ-7210-A. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-B 4 Speed shifter lever for any 1969 Mercury Cougar and Ford Mustang with V-8 engines. *Note - Must be used with Trunion C9AZ-7210-J, sold separately. Check out our video on rebuilding your shifter below: ...