1967 Ford Mustang

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 33797-S.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.

New Old Stock oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This black painted push on oil cap was on California sold cars with closed emissions systems. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked Autolite stamped on the top. Originals would have been stamped FoMoCo, this is a service replacement. Ford part number C4TZ-6766-A. *Note - a chromed version was also available with engine dress up...

Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.

New Old Stock oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was on California sold cars with closed emissions systems and engine dress up kits. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked Motorcraft stamped on the top. Originals would have been stamped FoMoCo, this is a service replacement. Ford part number C5ZZ-6766-D.Black version also available, see related parts. ...

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Rechromed, used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 or 390 and California emissions. This chromed push on oil cap was used on the DGS package or 390 GT engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California.

Correct detail. Chrome plated with oval-style FoMoCo script stamped into the top surface of cap. This is a push on cap and requires the type of cap that has a round filler tube protruding from the driver side valve cover. This is the correct Open Emissions oil cap for the finned "G" valve covers we sell.

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 engine. This black painted twist on oil cap was found on non-emission cars. Meaning 49 States except for California.*Note - a chromed version was also available with engine dress up kits.

This 49 state oil filler cap fits valve covers that utilize twist-on oil caps. This cap is a reproduction of the original cap that was found on 1967 models with the S code 390 and 289 engines with dress up kit like found on DGS 1967 Cougars.. This part features a quality chrome finish along with a crisp "FoMoCo" stamping. At its widest point it is 3" in diameter. The total height is 2 1/4" high including the portion that goes into the valve cover.* Trivia - For 289 engines it should have an...

Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...

This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.

Engine oil dipstick as found on most any 1967 Ford with 289 engines (C, A, or K Code). This has the correct small shield as found on 1967 and earlier cars, starting in 1968 this dip stick gained a larger 'bell' shaped shield that went over the dip stick tube. Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dip stick end is approximately 19.40 inches. The handles appear to have been painted black...

Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Painted engine oil dipstick as found on many 1967-69 Ford with 390 engines (S or X Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. From the top of the shield to the dipstick end varys from either 19.25" to approximately 20.25" (full, add, and safe marks are the same). The handles were painted blue originally. Typically the painted dipsticks were found on the non-GT (6.5 Litre) cars in 1968. Ford part # C7AZ-6750-A, Ford casting...

Original design in painted Ford Blue. Beautiful fit, a really nice part. Also known as oil level indicator tube. Replaces Ford part # C6AZ-6754-A.

Also available in Chrome. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375With the paint Stripped, it measures .365It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A.

Nice chrome finish. Also available in Ford blue. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375 With the paint Stripped, it measures .365 It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A. ...

Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.

Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675

Reproduction Small Block Chrome Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Includes drain plug.

This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.

Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Used oil screen pick up tube assembly from a small block Ford 260, 289, or 302 engine. This is for most front sump 260, 289, or 302 engines in Ford cars up to at least 1972. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item.* Excludes 351W and 351C engines, and all F Series...

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP