1967 Ford Mustang

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually. You can find the reproductions here.Ford Part number C7ZZ-6510182-A

Used Rod for the bell crank accelerator for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Rod fits in the tubular Link. It attaches to the Trunnion. Ford part number C7ZZ-9D774-A.

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

Uncommon jack as identified by the coarse threads. This version was made by a specific supplier AUSCO or Auto Specialties Manufacturing Company. AUSCO supplied jacks to Ford until 1970.See the link for the Ford jack research done by Marcus Anghel - Anghel Restorations

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

NOS lower inside door seal for any 1967-68 Mercury Cougar or Ford Mustang. No wrapper, this is not a reproduced item. Not very many Cougars or Mustangs came with this seal, we think it may have been for wind noise? Unknown. These are pre-drilled for mounting, no hardware included.Replaces Ford part number C7WY-6520272-A.

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521449-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

It is not often we get perfect used but nothing fits like OEM!The Engineering number on the bottom of the passenger side reads C7ZB-6521448-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces Ford Part # : C7ZZ-6521448-O Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

Excellent reproduction seals for your 67 - 68 Cougar or Mustang vent windows. Made from Ford's Original Tooling. Much better fit than other reproductions. Replaces For part numbers:C7ZZ-6521449-AC7ZZ-6521448-A

These are a higher quality rubber than the other reproduction available. Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

This is a 100% complete, functional set taken from multiple 1967 Mercury Cougars. Often it takes 2-3 cars to put together one set, decent driver quality set as the driver side will often show excessive wear and other belts can be rusted or missing. The set has been thoroughly inspected, cleaned and redyed with RIT dye in a boiling vat with vinegar. This set is driver quality and if one looks closely you will probably find a small crack in each of the re-tractor plastic covers, a few dots of...

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Used driver side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used driver side outer bucket seat SADDLE hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used AQUA passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Used IVY GOLD passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer...

Used SADDLE passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Used passenger side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat IVY GOLD hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat red hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

Installs between seat track and carpet. These are the same gauge steel as originals. Four per bucket seat, normally only seen on the 1967 model year, will need to be restored. Reproductions work fine, but look a little different. Ford Part # C5ZZ-13190-K

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Servo Assembly for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C735-A.

Used Shaft for the bell crank on the 1967-68 Mercury Cougar and Ford Mustang with speed control. The Shaft attaches to the Servo Bracket. It Bell Crank pivots on the Shaft. Ford part number C7ZZ-9D768-A.

C8ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. May be either large or small trunion. Subject to availability. Check out our video on rebuilding your shifter below: ...