1967 Mercury Cougar

Quality reproduction mirror for your 1967 Cougar. Whereas it is not easily detected at first glance, the head of the mirror does have a slightly different contour than original. The base is spot on perfect and the controller, cable assembly are all excellent quality. The wand (sold separately) is correct for 1967 (fluted, baseball bat shaped wand) as opposed to the 1968 version with a ball on the end (which we also sell). Plastic mounting pad and hardware included. *NOTE* Mustang mirrors...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

Reproduction sound deadener for the seat divider on the 1967 - 1970 Mercury Cougar. This reproduction is as close to the original as possible, and is comprised of a mastic material. This item is trimmable and will fit bot the 67 - 68 and 69 - 70 seat divider.

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Used spacer for the lower windshield moulding

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

NOS 1967-68 Mercury Cougar XR7 speedometer with trip meter. Original unused speedometer in FoMoCo box, all numbers at zero.  Ford part number C7WY-17255-C

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 4 speed transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-A or C7ZZ-17260-J. Has captured hold down bracket at transmission. Cable has a rubber hose at the transmission end. These measure out about 76 inches long. Also has a metal sleeve about 10 inches from the speedometer cluster end, Cable clamp? Used condition, will have road grime, and maybe a couple of abrasions or small...

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with C-6 automatic transmission. These are assembly line used and would have had a Ford number of C7ZZ-17260-C. Has captured hold down bracket at transmission. About 66-9/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the related items, you may need a firewall...

Spindle nut kit for the 67 - 69 Cougar or Mustang. This 3/4-16 threaded nut fits most of the 1967-69 brake spindles. The exception would be some of the Boss 302 and some 428CJ equipped cars. Included are nut, cap, washer and cotter pin.

Used chrome / black center cap for the 67 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers. The spinner was only available on cars made prior to 1967 as they were outlawed.Used in conjunction with Mercury cap part # C7WY-1130-C Check out the very first Cougar in our video below! ...

Used grade "A" simulated wire spoke hubcap with 3 bar spinner center / wheel cover that is in excellent condition with no curb scrapes, stress cracks in plastic center or pits in die-cast. The spinner was discontinued in 1967 so only the early models would have them in 67.Ford part # C7WY-1130-B

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.

"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand.These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

Discontinued by Manufacturer. Interior fastener kit that includes 240 fasteners. Below are all the sub-kits pictured individually. ...

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Restored wood rimed steering wheel for the 1967 Mercury Cougar. This is a one year only, Cougar only steering wheel that is correct for the XR7 or Standard Cougar. We must have a good core to start with. If yours is literally falling apart, it is a goner... This wheel does not come with the three spoke horn bar or button as pictured. The bolt on items are sold separate and are shown for display purposes only. Please call for available colors. *NOTE* We must receive your usable core before this...

Restored wood rimed steering wheel 1967 Mercury Cougar. This is a one year only, Cougar only steering wheel that is correct for the XR7 or Standard Cougar. We must have a good core to start with. If yours is literally falling apart, it is a goner... This wheel does not come with the three spoke horn bar or button as pictured. The bolt on items are sold separate and are shown for display purposes only. Please call for available colors. *NOTE* This item carries a $325 core charge that you will...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

Good used (but not perfect) wheel ready to bolt on as is and use on your daily driver. Will show some degree of minor separation on the wood-grain to colored portion of the wheel and at least one crack. Very rare that we have more than one of these in stock so the chances of getting the color you desire is rare. Please call prior to purchasing for colors, condition and stock on hand. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

New old stock, This unit is also known as a bumper filler, rock guard, or filler panel. Fits any 1967-68 Mercury Cougar.Ford part # C7WY-17779-A.

This single port version was used in the latter part of 1967 and all of 1968. Keep in mind we have units that are not as clean looking but still hold vacuum for about half the price. Cougar part number C7WY-13A185-C headlamp vacuum reservoir.

This screw / stud seems to always be missing. This stud is just a little longer than stock to allow installing the Hi-Po / 427 GTE air cleaner. Fit most Autolite 4V carburetors assembly. Zinc plated for years of service. Size: 4 1/2 inches 1/4-20 X 1/4-20 threads.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x7" styled steel wheel with a chrome outer rim and an original argent finish between the chrome spokes on the center. No, Mercury never offered them in a...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. No, Mercury never offered wheels in a 15x7" for an early Cougar... We now sell more of these custom made SS wheels than the original 14x6" version. Not only do they look...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.