1968 Mercury Cougar

Good used lens, will need to be polished but no cracks or deep scratches. Check out our video on dash removal and restoration: ...

Perfect in every detail down to the FoMoCo logo! Gorgeous reproduction made from high impact plastic. Make those sequential taillights come alive with these brilliant lenses. Sold individually, two required per car, left is the same as right. Replaces Ford part #C7WY-13450. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used taillight lens with no cracks or heavy scratches. With a little effort you can make a lens like this look new. For the best results use a three step polish like NOVUS. For decent results use a one step polish like Meguires. Sold individually right is the same as left on this application. Ford Part #: C7WY-13450. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

This taillight at first glance looks as good as our grade "A" lens but when it is held to the light you will see a few stress cracks. Most of the 67-68 Cougars on the road are this way and so are most of the lenses in our yard. This lens will not leak and will polish up just as good as our grade "A" lens. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer...

Used green dash turn signal indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Used on both the speedometer and tachometer lens. Comes with plastic keeper / washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration. This item may require epoxy. The mounting stud on rear may not be present. It is plastic and originally melted over.

Used parking / emergency light warning light lens spring for the 1967 - 1968 Mercury Cougar.Spring only, lens sold separately. 

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

NOTE: This is a blemished (blurred) license plate. We're selling these at close to nothing for anyone who wants to use the backside for custom painting. The graphics were printed blurry...you can't tell from a distance but up close they're not high quality prints (see photos above).  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification (in states...

Give your Cougar or Mustang that cool, classic look by adding these replica California black and gold license plates. These plates are favored by classic car owners everywhere, because they signify a rust free, restored classic car. These plates are real stamped aluminum with raised numbers and letters. Sold Individually.

NOTE: This is a misprinted license plate, please see photos above. The holes were accidentally printed over the real holes giving it a double blurred look (the Cougar graphic is fine). We're selling these at close to nothing for anyone who wants to grab a bunch as gifts or collectibles!  This classy aluminum license plate features the WCCC running cat logo on a matte black background, with a slightly grainy texture. Works great for display at car shows, everyday beautification...

Used license plate holder and fuel door for all 1967-68 Mercury Cougars. Comes as shown, hinges inspected, will include used or new license plate plastic inserts. See our list of related parts, will need rubber bumpers.Replaces Ford part number C7WB-13393.

Sold individually.

Reproduction license plate frame for your Mercury Cougar.  Sold individually. Note: These will not clear on the rear pull down fuel door on the 1967- 1968, so they will only work for the front license plate on the 67-68 Cougar. These can be used for front or back on the 69-73 Cougar.Check out this video of our 2013 Open House event. Se you next year! ...

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California.  Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.

Good used license plate light socket and wiring pigtail from a 1967-68 Mercury Cougar. Good socket without damage or corrosion. We cut the single wire pigtail as close to the main tail light harness as possible. Easy single wire splice for the DIY Cougar owner.

This lid was also used on the Hi-Po small block Mustang. The painted version is what you will find for the inner lid on the 68-71 Cougars equipped with Ram Air.

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

This was the inner air cleaner lid used on the Mercury Cougars equipped with a 428 Ram Air Cleaner or 429 Cobra Jet Ram Air Cleaner assembly. Although you will often find chrome under the blue engine paint on these lids they are in fact supposed to be painted from the factory. This lid is 14-1/8 inches in diameter. The reason you will often see chrome underneath the paint is that this is the same lid used on the 1967 427 GTE, 289 HiPo equipped early Mustangs and 390 GT / GTA Fairlanes and...

This particular mid-plate has a seemingly factory installed tab welded to the backside.  This unit was not found on a 1968 Mercury Cougar but does have the wrinkles indicative of a 68 lid.  The tab located at 12 o'clock makes it rather difficult to install the Air Cleaner to hood seal. If anyone can clue us in to the exact application of this oddball part please chime in!  Check out: http://428cobrajet.org/id-air-cleaner-68.html to learn more about the subtle differences between...

This lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several applications,...

This Grade A quality ashtray lid was located at the rear of the console and was used on all 1967 - 1968 Mercury Cougars except the 1967 standard model and the 1968 XR7G. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish and a slightly taller lower section. The removable ash receptacle is sold separately.Ford part # C7AZ-6330714-A.

This Grade B quality ashtray lid was located at the rear of the console and was used on all 1967 - 1968 Mercury Cougars except the 1967 standard model and the 1968 XR7G. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish and a slightly taller lower section. The removable ash receptacle is sold separately.Priced as driver quality units, most will have light pitting or scratches as shown.Ford part # C7AZ-6330714-A.

Nice reproduction 1967-68 Mercury Cougar console light housing with lens cover. Plug and play with wiring. Click on images to enlarge. ...

Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

"C" pillar courtesy light bulb which is also good for under under dash courtesy lights on 67 - 70 Cougars.

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

NOS Rand McNally Lincoln Mercury atlas and travel guide, originally distributed to customers through their local dealer. Includes state, city and "special maps" that include the US, Central America, Mexico and Puerto Rico. Also includes a special features section with points of interest.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Latch rod that links the door latch and the inside door handle, right or left side door. 1968 Mercury Cougar and Ford Mustang door latch rods are straight, and do not have a clip midway, compared to the 1967 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C8ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click...

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Reproduction trunk lock cylinder with keys for the 67 - 68 Mercury Cougar. Replaces Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit). Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the cylinder and partially turned as if to...

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.