1970 Ford Mustang

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

Pair of reproduction cowl vent panel support pads.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

D0ZZ-5482-B Factory used front sway bar found on most 1970 Cougars. 3/4 inch in diameter. This factory used front sway bar, does not include mounting anybrackets or end link kits.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

D0AZ-2B264-A Identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here. Replaces Ford Part number C9ZZ-18578-A

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

This used intermittent wiper switch has a two speed wiper function, and when turned counter clockwise, has a rheostat that sets the different delay times. A 1969 switch can be used, but the shaft will be about 3/8" shorter, you may need to use a 1969 metal knob to use in a 1970. Sometimes called interval or delay wipers.*NOTE* Must be used in conjunction with a Intermittent wiper controller.Replaces part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A

Tested and inspected neutral safety switch for the C-6 transmission installed in 69-70 Mercury Cougar and Ford Mustangs. This neutral safety switch is identified by having a single plug, Identified with a single plug with weatherproof seal, the earlier versions do not.Look for a transmission code of U on your door data plate. If your car has a code W, your original transmission was an C-4 and uses a different neutral safety switch.Replaces Ford Part #: C9ZP-7A247. ...

New Old Stock neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

Quality reproduction for all 1969-73 Mercury Cougar and Ford Mustang with FMX automatic transmissions. This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug and wire that will not be utilized when used on a 1969-71. All but one plug will be utilized on the 1969-71 applications. This plug and wire is not needed and can either taped off or clipped. Replaces original Ford part numbers C9ZZ-2A247-C,...

Reproduction power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch.However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1969-70 Mercury Cougar and Mustang with visibility group option. Includes bolt to attach to emergency foot brake. Ford part number: C6GB-15652-A

Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Very nice reproduction item, comes as shown with the knob marked "TOP". *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

PICTURE SHOWS a REPRODUCTION CONVERTIBLE TOP SWITCH - Our USED switch will NOT include a "TOP" knob.USED - Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob, or if it does, it will be in poor condition. This switch was also used on Cougars with factory power sunroofs.*Note - The 1970 Mercury Cougar XR7 had the...

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. ...

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.