1970 Ford Mustang

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Core C-6 Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "U" transmission code on the door tag. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the special valve body for 1970 428CJ and 1971 429CJ engines. Ford...

Core FMX Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 or 1971 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Reproduction Ford blue painted valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

Reproduction pair of aluminum 428CJ valve covers. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Sometimes called 1969 Shelby valve covers. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

Finned aluminum Ford cast valve covers for any 1970-71 Ford or Mercury with 429CJ engine. Almost correct on 1971 Mercury Cougar and Ford Mustang with N or C code 429CJ engines. D0OE-6583-A is the part number cast on both. These both have the same opening for the oil filler cap on both sides. Technically, for 1971, the passenger side cover would have a round hole for the PCV grommet and have a D1OE-6583-CA casting number.

Reproduction chromed valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

Short steel chromed valve stem for Ford wheels or any steel wheel with a 0.453" hole. Clamp in or bolt in style, sticks up 3/4 from wheel surface, 200psi maximum pressure. These will work with our aftermarket Ford wheels without trim rings. These are not compatible with our aluminum wheels.Premium grade, marked for "High Temperature".

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Reproduction vinyl sleeve for the choke cable on the 1970 Cougar or Mustang equipped with a 390 or 428CJ. This sleeve protects the cable from rubbing on anything and prevent possible fraying.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New reproduction instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Features Solid State electronic circuitry. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator...

Features the proper cover and original logos. I A S F stamped on cover. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with the 68 A/C Voltage Regulator. Replaces Ford Part #: D0AF-10316-A. The voltage regulators listed in this section are poor quality. We suggest you buy a reliable, modern, solid state unit and just use the cover we sell as a stand alone product. We will not warranty the mechanical voltage regulators you...

Voltage regulator for the 1968, 1969, and 1970 manufactured before 9/15/1969 that is not equipped with factory AC. This regulator has "C8AF-10316-A" printed on to it, actual Ford Part number is C3SZ-10316-B or D4TZ-10316-A. This is Ford Regulator Number GR-341. These new voltage regulators are improved and more reliable than the units we've sold previously.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8AF-10316-A (cover only)

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...