All Products

Rare find in NOS form. Sold as a pair only. Driver side carries a C7WY-16304-C Ford part number and the passenger side carries a C7WY-16304-D part number. The casting number on the driver side is C7WB-178951-A and the passenger side has a C7WB-17B957-A casting (or engineering) number imprinted on the top of the part.

C9ZE-6A360-A Very unique part and a component to the 'drag pack' option on the 428SCJ engines. This is an additional counter weight used on conjunction with the SCJ crankshaft, SCJ crankshaft balancer. Ford part number C9ZZ-6359-A.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Since the reproduction is no longer available anywhere, we've taken a used plug and our electrical department has pieced it together to make a useable plug. The Eliminator uses the XR7 harness but not the XR7 rocker switches in the center of the dash. This bypass plug completes the circuit left open when no XR7 switches are plugged into the harness.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Tilt steering column cover plate for turn signal lever. Two versions, two different sizes of openings for the turn signal wand. Original used Ford part, plan on painting to match your steering column. Fits all 1970-71 Mercury Cougar, 1970 Ford Mustang, and other Ford/Mercury cars with factory tilt steering columns. Replaces Ford part number D0AA-9D793-AW.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

OEM Ford factory cowl brace as found on 1970 Mercury Cougar Boss 302 Eliminator and Boss 302 Mustang. Used item, not reproduction. Mounts with the lip up, towards the front of the car. Very limited supply.

If your Cougar has to sit outside for any length of time this is a must. Not only will it protect from unwanted moisture but pine needles and other debris will be kept out. If your cowl already leaks then this is a great way to prevent the floors from rusting. Spring loaded T shaped fasteners make for instant installation and removal, attaches under grate bars so as not to damage paint. Very worth while preventative maintenance item.

Used original FoMoCo upper cowl cut for all 1971-73 Mercury Cougars and Ford Mustangs with A/C. Bear in mind that the inner metal section, or the undersides, did not get paint and is the upper cowl section as shown. A/C cars differ, they have a fresh air duct arrangement. Note that this part will not be perfect and will require hours of spot weld removal due to how large we cut them. The shipping will also be much more than our repro. We highly suggest buying the repro as you can easily modify...

Used original FoMoCo upper cowl cut for all 1971-73 Mercury Cougars and Ford Mustangs without A/C. Bear in mind that the inner metal section, or the undersides, did not get paint and is the upper cowl section as shown. A/C cars differ, they have a fresh air duct arrangement. Note that this part will not be perfect and will require hours of spot weld removal due to how large we cut them. The shipping will also be much more than our repro. We highly suggest buying the repro as it is a direct...

Crankshaft oil slinger for all 429, 429CJ, 429SCJ, Boss 429, or 460 engines, the "385" series. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number C8SZ-6310-A.

Application for all 1971 - 1973 Cougars with factory C6 automatic transmission. Also the correct application for those wanting to install a small block C6 in their 1967 - 1970 Cougar. Original engine options include 351-2V, 351-4V, and 429CJ. We have found two versions of this crossmember, one with three holes in the middle section where the rubber isolator mounts and one with two. This part weighs 2.96 pounds and when set on a level surface, the height of the mounting hole on the driver side...

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

Application for all 1971 - 1973 Cougars with a factory manual 3 and 4 speed transmission. Engine options include 351-2V, 351-4V, and 429CJ. Ford part number D1ZZ-6A023-B. If you have pictures, specs or one of these for sale we would like to hear from you.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

Single cylinder head from 1968 Mercury Cougar 302-2V engines with smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. The 'with smog' cylinder heads would have been found on 3 and 4 speed manual transmission cars. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 61.7-64.7 cc's. With stock pistons, these heads will net an approximate compression ration of 8.7:1. Basic cylinder head number is 6090. Several Ford casting numbers...

Single cylinder head from 1968 Mercury Cougar 302-4V engines with smog. Sold as a core, needs thorough cleaning and rebuilding prior to use. The 'with smog' cylinder heads would have been found on 3 and 4 speed manual transmission cars. They came drilled and tapped for thermactor smog systems. Typically this cylinder head has 1.78 and 1.45 inch valves, and the chambers measure out at 52-55 cc's. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder...

Single cylinder head from 1970-71 Mercury Cougar with M code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 62.8 cc's. These are considered 'Closed Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 10.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-N. 4V in the...

Single cylinder head from 1973 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.66 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.0:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D3ZE-6090-AA. 4V in...

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. These are the GT exhaust manifolds with 14 drilled and tapped exhaust bolt holes. Current dates include: 6F17, 6A11, 6A10 Ford casting numbers...

Single cylinder head from 1967 Mercury Cougar with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current dates include: 7C8, 7C22, Ford casting numbers...

Single cylinder head from 1968-70 Mercury Cougar with 428CJ engine with smog holes. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.09 and 1.65 inch valves, and the chambers measure out at 73-76cc's. With stock pistons, these heads will net an approximate compression ration of 10.6:1. Basic cylinder head number is 6090. These are the Cobra Jet exhaust manifolds with 16 drilled and tapped exhaust bolt holes. We won't have these in stock...

Single cylinder head from 1971 Mercury Cougar with 429CJ engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.24 and 1.72 inch valves, and the chambers measure out at 73.5cc. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090.  Also fits all 1970-71 Ford or Mercury with the J or C code 429 Cobra Jet engines, including Torino and Cyclone.Ford casting number...

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. New Old Stock OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder. Thread pitch 1/2" x 20

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

Our 8000 tachometer has proved to be a very popular upgrade for those who have a 1969-1970 standard or decor interior. Of course, if you put a tachometer in the instrument cluster slot intended for a clock, where does one mount the clock? We now have this kit that includes a CNC precision cut straight grain panel, an under lying bezel cut from a xr7 panel and a xr7 / Eliminator clock housing and mounting bracket with hardware. This kit will allow you to mount the standard clock that normally...

Only for use on standard model Cougars with AC. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Used grade A dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy this...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used grade B dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be nice but will have at least one small crack, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find...

NOS dash face pad for the standard Mercury Cougar equipped WITH air conditioning. This unit will be like new and will not have any cracks. Includes surround trim, but without mounting clips. *NOTE* Attaching clips for this unit are like hen's teeth. We suggest using velcro strips that will secure this unit to your dash.Check out the "Cougar Dash Surgery, Clock and Speaker Install" video by Andrew Chenovick: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used grade B dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice but will have at least one small crack, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.  Current color appears to be Aqua Blue. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "A" grade used is one without cracks or chips. Put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'. Ford casting number D0WB-65044D70.

Plastic filler piece that goes over the steering column and bridges the instrument cluster portion of the dash pad. Ford calls this part a "PANEL" (Instrument Panel Cluster) in the Master Parts Catalog. "B" grade used is one with a crack and at least one other chip (see picture), you can put a desired color in the comments section of the online order. We suggest planning on 'painting to match your interior'.

Many people seek this part when changing their XR7 over to factory installed AC. Not only will we give you a substantial credit when you send in your non AC center bezel, we will also carefully match our stock to your bezel to ensure ours does not look out of place when place next to your existing panels. If you send in a substantially faded panel for exchange we will credit back $$$.Finding Grade A dash panels which do not have any fading is nearly impossible. Check back we do get them...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

This is soft, straight pad with no burns, scrapes or blemishes. This is for the guy that is building a show car and is striving for perfection and wants to do nothing but freshen it up with a coat of SEM Flexible Coating. Often, we will not be able to provide this pad, and almost never will we be able to provide it in some of the more obscure colors, but please do ask prior to purchasing as to what colors we have on hand if it is important that you get the correct color.

This grade A pad for a 71 - 73 is truly a rare find. We only obtain an excellent pad like this every year or two. Grade A pads will have no cracks and will not be curling on the edges. Contact us for color on hand as the picture shown is not the actual pad you will get.

Good used original upper black dash pad for the 67 Cougar. The difference between the 67 and 68 is that the 68 dash pad has a relief cut for the aluminum VIN tag located on the passenger side and 67 did not. Grade B dash will have no cracks, possible missing corner stud and not soft and pliable.