Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Reproduction disc brake master cylinder cap in gold cadmium for the Mercury Cougar or Ford Mustang. We have compared this cap to our originals, and the stamping does not match any of our originals, but the manufacturer claims that the scripting is correct. Also available in chrome! This cap will only fit master cylinder part# 15298Replaces Ford part # C7AZ-2162-B. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar...
Reproduction premium quality disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. These are considered concours correct and show quality. Check out the link below for some information on master cylinder caps: http://anghelrestorations.com/uploads/3/5/1/2/35122002/master_cylinder_caps_1.5.pdf Replaces Ford part # C7AZ-2162-B. Fits: 1969 Mercury Cougar1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang / Torino1970...
Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...
Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B
Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.
Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.
1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.
Sold individually Zinc (dark silver)
Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...
1969 351-2V Autolite 2100 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-A stamped on the carburetor base, 1.23" venturi size and 356 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.
1969 390-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-E stamped on the carburetor base, 1.25" venturi size and 600 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top.
New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...
Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.
Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.
5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786
This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts.
This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.
This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (2 1/2"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with a 1" spacer.
This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.
Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually
Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...
15/16" thick aluminum with 5/8" heater nipples & 5/8" PCV hose nipple on rear. Casting number C9ZE-9A589-A.
Good Quality spacer that measures 1 1/8" tall. Comes with PCV hose clamp and vacuum port cap. This was used on all 289, 302, 351w motors with a 4V carburetor.
Factory cast aluminum four barrel carburetor spacer plate, one inch tall. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. *excludes Boss 302 Eliminator ...
New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.
New carburetor spacer plate gasket for all 1969 Mercury Cougar or Ford Mustang with S code 390-4V or 390IP original Autolite Carburetors. Additionally it fits all Ford installed Holley carburetors. This is the carburetor spacer to manifold gasket. Upper gasket between spacer and carburetor also available. This carburetor gasket also works well with most aftermarket Holley and Edelbrock carburetors.
New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.
New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite 4300 carburetors.
Concourse Correct Hollow Left Rear Stud for the Carburetor Vacuum port to the C6 transmission modulator hose Replaces Part # 382768-S8
Used 3/8-16 x 41/64" carriage bolt for the shock tower shock cap. Three bolts used on each cap, 6 total per car. Sold individually. *Note - Carriage bolt detail cleaned for the picture, actual part will need a clean up on a wire wheel.Replaces Ford part number 378535-S2.
Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4385S. This is the style with "CARTER" and USA, has the 3/8" fuel nipple. Correct for 1968-69 Mercury Cougar with X or S code 390 engines and 1968-69 Ford and Mustang with 390 V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible dates, we will...
Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4567S. This is the early style with "CAR bure TER" and Canada, has the 3/8" fuel nipple. Correct for 1968 Mercury Cougar with H or M code 351 engines and 1969 Ford and Mustang with 351W V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...
New castle nut for all power steering control valve ball stud found on 1967-70 Mercury Cougar and Ford Mustang. 3/4 inch hex nut, with 1/2-20 threads. Connects the Pitman arm to the ball stud on the P/S control valve. Don't forget the cotter pin. Verify your shop manual for correct year torque specifications. We found one source of 28-35 FT LBS. for the Pitman Arm nut to control valve. Ford numbers for attaching nut: 1967-68 351059-S, 1969-70 385002-S.
Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang. Dimensions: 9/16" - 18.
C9ZZ-3304-A Manual steering drag link for most 1969 Cougars and Mustangs (excludes G code Boss 302 cars) with a non-power assist manual steering system. 1969 Boss 302 Eliminators and Mustangs used a heavier duty drag link that was adopted for use starting in 1970, on all Cougars and Mustangs. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.
C9ZZ-3304-B Power steering drag link for most 1969 Cougars and Mustangs (excludes G code Boss 302 cars) with a factory power steering system. 1969 Boss 302 Eliminators and Mustangs used a heavier duty drag link that was adopted for use starting in 1970, on all Cougars and Mustangs. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.
Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.
Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good! When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...
Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...
This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...
Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background. *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...
Reproduction Cobra GT 350 center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic blue cobra with red detail. *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...
Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a gold background. *NOTE - These caps are specifically designed to fit the LW10 series wheels.
Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...
Officially licensed center cap is an exact replica of the center cap installed on 1966 Shelby 10 spoke wheels. Authentic down to the smallest details. Each die-cast cap features the famous Shelby "CS" race track logo and a show quality chrome finish. The cap is secured in place with a backing plate and hardware to eliminate the risk of it coming lose or being stolen.To be used with the Legendary Series Shelby wheels. Shelby CS LogoFits GT7 - LW10 Series WheelsFits GT6 - LW66 Series Wheels Sold...
Usually ships in 3-5 business days. Reproduction Automatic Transmission Center Console With Woodgrain Insert and Flat Lid for the 1969 Mercury Cougar or Ford Mustang
Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...