Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...
This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.
Reproduction mounting kit contains everything you need to install the cowl cover on the 69 - 70 Mercury Cougar.
Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.
Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...
Replaces Ford part # 55806-S
Used mounting plate for the heater blower motor on the 69 - 70 Cougar or Mustang without A/C.Keep in mind that this same plate can be used on a 67 - 68 Cougar and Mustang heater blower motor with A/C.
This specialty screw attaches the gas pedal to the throttle linkage. Fun fact: the head looks like Phillips (and that works fine) but this is actually designed for a Pozi bit.
Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.
Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!
Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...
Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.
C5AZ-10A370-C Alternator mounting spacer, goes between the cylinder head and alternator housing. Fits 1968-70 390-2V, 390-4V, and 428CJ engines. Smog OK. There is no casting number but one is listed C5AE-10A370-C. Inside diameter 7/16". We measure them out at 1-5/8 inches long, supposed to be pink anodized or tinted.
Steel spacer between cylinder head and pump. Inside diameter 3/8", length approximately 1-13/16".
1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)
10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).
The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...
This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...
This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.
Locking nut for attaching the door window regulator to the window channel bracket on any 1969-70 Mercury Cougar or Ford Mustang. While we do not sell the T-bolts for attaching to the regulator (T-bolt Ford Part # C8SZ-6523274-A), we do have a retainer to keep it in the front channel bracket. Find it here. This is not an exact replica of the t-bolt lock nut, but is a functional replacement part. Replaced Ford part #: 34975-S ...
[No Description Provided]
Replaces Ford Part # 381985-S Sold individually
Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...
383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.
383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.
Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.
Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .
Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .
Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.
Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.
This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Replaces Ford part # C2DZ-6A529 Sold Individually.
Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish
Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.
Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut.
New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.
Perfect fit.
Correct nut that is designed not to come undone.
New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S
Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.
Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.
Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.
380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.
Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.
Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.
Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.
Reproduction heater duct nylon rivet #375064-S is sold individually.
Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.