Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.
Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A
Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.
Reproduction 351 2V AT / MT Emission Decal for the 1971 Mercury Cougar / Ford Mustang
Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...
Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.
New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury switch that turns the light on when the lid is raised and off when lowered. Replaces Ford accessory part #: C2RZ-15A700-A.
After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered. Replaces Ford accessory part #: C2RZ-15A700-A.
Used engine lift hook or hoist bracket for all 1970-73 351C engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351C-2V and M or Q code 351C-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also...
Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Right hand bracket. Ford part number D1ZZ-6028-A.Does not come with hardware. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.
Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Left hand bracket. Ford part number D1ZZ-6029-A. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.
Original engine frame mount brackets for all 1971 to 1973 Cougar *convertibles regardless of engine and all 1971 Cougar 429 Cobra Jets. Includes one each: D1ZZ-6028-A & D1ZZ-6029-A engine frame brackets. Visually, there are also a version where there is a double set of holes on top. *Excludes non-convertibles with 351 cubic inch engines.
Factory original part for all 1971 - 1972 Cougar hardtops with 351 engines. 1971-72 Mustang with 302 or 351 engines. Left hand bracket. Ford part number D0OZ-6029-B. Does not come with hardware.*Excludes convertible models.
Original 1971 to 1972 hardtop small block or 351 V-8 engine frame brackets. Includes one each: D0OZ-6028-B & D0OZ-6029-B engine frame brackets. These will fit directly into your 1973 Coupe which you can no longer find motor mounts for. Once you place these 71-72 stands in your 73 coupe you can now use the reproduction isolators (motor mounts) commonly available. Does not come with hardware. Also fits 1971-72 Mustang with 302 or 351 engines.*Excludes 1971 - 1972 convertible Cougar and...
Factory original part for all 1971-72 Cougar hardtops with 351 engines. 1971-72 Mustang with 302 or 351 engines. Right hand bracket. Ford part number D0OZ-6028-B. Does not come with mounting hardware. *Excludes convertible models.
Reproduction pair of engine Frame Stands for the 1971 - 1972 Mercury Cougar or Ford Mustang.Replaces ford part numbers: Driver side D0OZ-6029-B / Passenger side D0OZ-6028-B Does not come with mounting hardware. *Excludes convertible models.
After being obsolete for years we have brought back another hard to find clutch equalizer component for 1971-3 Mustang and Cougar. Numerous other Ford application too. Replaces Ford part # C5AZ-7B545-A
Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.
Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.
D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.
D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.
D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.
Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.
Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1971-73 Mercury Cougar and Mustang. It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # D1OA-19849-AA. aka YG-27
This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW
New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...
New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...
New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...
Under dash mounted rear speaker controller. This is a used and tested unit that functions flawlessly. Typically this style of fader switch was used with the stereo radios with either AM/FM or the various 8-Track stereos, with added rear speakers. Included is the blue plug and pigtail that goes to the speakers.The pigtail harness is marked D1AB-19A017-BC.
White reproduction fan for the Thermactor Smog Pump.
This is an excellent reproduction made from the original Ford tooling and features the original Ford logo. This is correct for all the cross flow radiators used in 1971 - 1973 except the 1971 429CJ. Opening measures about 20-1/8" in diameter. Replaces Ford part # D1ZZ-8146. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.
Fan shroud hardware kit for the 302 or 351 on the 1971, 1972 or 1973 Cougar and Mustang.
Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.
Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.
Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.
Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.
Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.
Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.
Fan spacer, measuring 2-5/8 inches. Application 1972 - 1973 Mercury Cougar and Ford Mustang with 351-4V or 351CJ, and all 1971-72 351's with air conditioning. Reference number YA-75.Ford part # D2AE-8546-AA, Ford engineering # C4AZ-8546-G.
Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.
Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.
Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.
Self threading white plastic. Used on front and rear valances.Sold individually.
Contains nut and washer. Fits all Ford alternators. AMK F-644.
AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.