Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.
3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car.
3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.
Decal Text: Autolite EV-50 D0AZ-6A666-A Replaces Ford Part #: D0AZ-6A666-A.
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.
Cork valve cover gaskets for any 351C or 351 Cleveland Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Rubber valve cover gaskets for any 351C Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Concours correct Autolite spark plug wires for any 1971 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q70 (second quarter 1970) on the 7mm wires. Orange spark plug boots on this set.
This is the reproduction bare metal oil pan for the 1971 Merucury Cougar and Ford Mustang equipt with the 429 big block. Does not include drain plug or a baffle.
This is a reproduction bare metal oil pan with a baffle for the 1971 Mercury Cougar or Ford Mustang and a 429 big block. Includes the drain plug.
These are the best CONCOURS radiator hoses on the market. Made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Features special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Imprint is CONCOURS correct for the specific application year includes the Autolite logo. Hoses are also approved by Ford Motor Co. Replaces...
Cork valve cover gaskets for any 429 or 460 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
New rubber oil pan gasket for the 1971 Mercury Cougar or Ford Mustang when equipped with the 429ci engine. Rubber/Steel Core, 3/32" thick.
Rubber valve cover gaskets for any 429 or 460 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...
Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego
Alternator adjusting bracket found on 429 engines. Not technically correct for 1970-71 429CJ engines, this is the passenger car version. The true 429CJ alternator bracket is slightly different and extremely hard to find. This is a very good and economical substitute. Has Ford part number D0SE-10145-A stamping.
384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.
This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...
Reproduction carburetor stud for all Ford numbered Holley carburetors 1967-71. 1/4-20 double ended stud from AMK. Stud only, no wingnut.
This is a reproduction of the original engine displacement round decal, Chrome background with gold followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard followed by black background with gold CJ 429-4V followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard. located on the top of the air cleaner.Outside diameter: 13 1/4"Fits...
Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.
Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.
This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...
These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits Mustang 1965-67 K code HiPo 289 and 1968 Mercury Cougar GT-E W code 427-4V engines, that were originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A. ...
Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.
This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Please note that the Ford Service Replacement specs for this filter (Service Replacement # D7AF9601AA) are; Type: 67; Inside: 13.000; Outside: 11.200; Height: 2.795. All reproductions that we have found follow these specs, making the filter 1/8" taller than the original filters. These filters will function properly, but the lid will not seat properly. ACTUAL FILTER SPECS: Air Filter Height (Inches) : 2.822...
Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock
Good used 10 blade alternator fan.Ford Part #: DOAZ-10A310-B.
Contains nut, lock washer, and spacer. Fits all Ford alternators.
This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.
D1AF-9600-FA Air cleaner base for all 1971 Cougars with the H code 351-2V engine. About 17.84" inches in diameter. Could also be found with casting number D1AF-9600-FB or D1AF-9600-FC. IMAGES BELOW ARE FOR REFERENCE ONLY, EXTRA PARTS ARE NOT INCLUDED Ford part number D1AZ-9600-F. ...
Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For any 1970-71 Mercury Cougar or Ford Mustang with 302 or 351 engine and 43-55 AMP alternators. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces...
Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. 1970-71 Mercury Cougar with 65-75 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-75 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : D0ZZ-14300 ...
This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.
Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang
NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Replaces Ford Part #: D0OZ-10732-B.
Exactly like the originals. This group 27 battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Supplier misidentifies this part as D1ZZ-10732-B. Replaces Ford Part #: D0OZ-10732-B.
Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.
Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.
Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.
Sold individually # 56354-S
part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.
Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut. This is not the round headed slotted screw type that Ford also used.