1967 Ford Mustang

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Latch rod that links the door latch and the inside door handle, right or left side door. 1967 Mercury Cougar and Ford Mustang door latch rods have some slight bends, and a clip midway with a Phillips screw, compared to the 1968 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C7ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar...

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out our video on rebuilding your shifter below: ...

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

[No Description Provided]

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory C code 289-2V V-8 engine. Rated at 200 Hp with 9.3:1 compression ratio in 1967. 1967 289 engine that may or may not have been in running condition when pulled. Guaranteed to be rebuildable, most of these will already be bored 0.030", and need more. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 2 inches from wheel surface. These will work with all of our aftermarket Ford wheels especially with trim rings. These have the Dill 627 caps. Same as the 1960's cars.

375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below.  ...

This is the reproduction exclusive to the 1967 Mustang. Will also work on Fairlane, Comet, Futura and Falcon. C7OZ-3078.  NOTE: Will not work on the 1967 Cougar without the use of 1967 Mustang strut rods.  Get your control arms for 1968 - 1973 here.

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 9/16 across the leading inside edge, and 1 5/8 across the outer rim.Note: These larger diameter bushings were used on Ford service replacement lower control arms. Typically found on Ford supplied lower control arms without the welded on jacking tabs.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

[No Description Provided]

Reproduction Lower Headlight Bucket Loom Clip for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

Sold as a pair, these are one year only brackets used with the over-sized 390 radiator. We also have the 1967 unique rubber insulators listed as well. These brackets have a 2" opening. Check out our video on Radiator and Fan upgrades below: ...

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Chrome tapered acorn lug nut for use with the new Legendary wheels. This 13/16" nut really only fits the Magstar style - the others have tighter clearances and you'll want to use the 3/4" nuts made for these wheels. Sold individually here, or in a complete set with valve stems. Replaces Ford Part #: C9ZZ-1012-B.Check out our video on Legendary Wheels below: ...

Correct 3/4" tapered chrome acorn lug nut for the new Legendary Wheels. These are what we recommend you use with these wheels, since the clearances are too tight for regular 13/16" lug nuts. Sold individually here, or as a complete set with valve stems.Check out our video on Legendary Wheels below: ...

Reproduction lug nut for the Legendary GT7 Series wheel. Sold Individually. You can find the complete lug nut installation kit here.Check out our video on Legendary Wheels below: ...

Chrome acorn lug nut for most any Ford steel wheel including styled steel, Magnum 500,  new or reproductions.Replaces Ford Part #: C9ZZ-1012-B.

Standard stamped steel wheel lug nuts in good used condition. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar Should have a set of 5 in the trunk for use with your stock steel spare...

Used lug nut for your 1967 - 1970 Cougar

A close economy reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These stand just a little shorter than our other, more accurate reproductions.They don't have the correct matte finish, have a smaller head section and longer edges, but do still have the pointed top. If you are not building a show car then you may want to go with this generic version. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury...

Finally! A close reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These premium lugs nuts stand just a little taller than the originals, hard to detect unless you have them side by side with NOS.They have the correct matte finish and pointed top. If you are not building a show car then you will want to buy the brighter, generic version that you can find here. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969...

These open lug nuts are commonly used on drag strip or race cars . They will accommodate the aftermarket extended studs which are prevalent in all forms of racing. Plated bright silver zinc. Extended Thread design will work on any Legendary Wheel. 3/4 hex allows plenty of room for sockets. 1/2 x 20 threads. Check out our video on Legendary Wheels below: ...

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction nylon lug nut protectors. These are sold in pairs, and come with 3/4" and 13/16" sizes. Simply slide one of these sleeves into your socket and keep the chrome on your lug nuts in perfect condition!These protectors are simple plastic and are prone to breaking. Can be used on a variety of other vehicles with the same lug nut size. For the 3/4" lugs, use the sleeve with a 7/8" socket. For the 13/16" lugs, use the sleeve with a 15/16" socket. ...