1967 Ford Mustang

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Motorcraft new old stock brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a service replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. C7ZB-13480-B Replaces Ford Part #: C9VY-13480-A.

NOS brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Ford part # C7AZ-2B264-A.

Used brake warning light switch for the Mercury Cougar or Ford Mustang that is identified by the single pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder, this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.Ford part # C7AZ-2B264-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Used one year only door jamb mounted switch for activating the tilt column.

Pull on switch assembly for the speed control option on probably the early system. Switch only, no knob. Ford part numbers C7WY-9A837-A and C7WA-9A837-A *Note – for use with factory cruise control.

NOS fixed column turn signal switch for the 1967 Mercury Cougar or Ford Mustang. This is a later service replacement turn signal switch, it may have an extra wire or two, and the wire lengths may be longer than the factory original. Ford part number C7ZZ-13341-F Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

OEM Ford stove type bolt for the securing the early style belt tensioner pulley. Used on Cougars and Mustangs produced before 1/3/1967. For use with C5AA-8A919-B Air conditioning belt tensioning pulley.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. 1967 Mercury Cougar and Ford Mustang with S code 390-4V engines. Hooked end goes into the carburetor linkage, threaded end to the rear. Ford part number C7ZZ-9A702-A. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. Application 1967 Mercury Cougar and Ford Mustang with 390-4V and cruise or speed control. Ford part number C7ZZ-9A702-D. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

Used Trunnion for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Trunnion is the white plastic bone looking thing with a hole in it. Attaches the Link and Rod from Servo Bell Crank. Ford part number C7ZZ-9D766-A.

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Reproduction turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness.

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.