1967 Ford Mustang

Two piece pre-bent OE steel brake line kit that runs down the rear axle on the 8 inch rear end of a 1967, 1968 or 1969 Mercury Cougar or Ford Mustang.The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for...

Used brake pedal for the Mercury cougar equipped with power brakes and a manual transmission. This is for use with the non-collapsible 1967 steering column and with a clutch pedal. Longer arm than manual brake pedals. Keep in mind automatic pedals can be trimmed down to work as manual transmission pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim.*NOTE* You will have to drill holes in your existing manual brake pedal hanger to accomomdate the power brake pedal....

Good used setup as taken from a parts car. Will have good bushings in the hanger and show average wear is all the normal places. We will not send you worn out junk...

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...

This is a complete kit for front and rear. If you own a 71 - 73 and then you will need two more bolts. mercurycougar.net: I was in Salem on business Monday when I decided to give West Coast Classic Cougar a call. Don was gone but Lin was there, talk about a nice guy I looked around the shop and Lin got me the parts I needed for my 68 Coupe. I am sure Lin was busy but he took the time to answer any questions I had, swapped a few stories and gave me a real good deal. I recommend anyone needing...

(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

Used passenger side (right hand) disc brake caliper mounting bracket that is a unique and one year only bracket for mounting the Kelsey Hayes twin piston caliper to the 1967 Cougar brake spindle. Tough parts to find in rebuildable condition. We won't always have them in inventory as singles unless we have multiples of these extra brackets for one side or the other. Ford part # C7OZ-2B134-A.

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-E stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - Not for DSO 52 or DSO...

1967 289-2V autolite 2100 carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base, 1.02" venturi size and 240 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 289-2V Autolite 2100 carburetor, manual transmission - California DSO 52 and 53. C7DF-G stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and manual transmissions. *Note - For...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-H stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-N stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-2V carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base 1.14" venturi size 300 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars. *NOTE - Take a kid for a ride in a classic...

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-S stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note - Not for DSO 52 or DSO 53 cars destined for California. *NOTE* Take a...

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C7DF-C or AG stamped on the carburetor base, 1.00" venturi size 470 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines and manual...

1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- 49 states. C7DF-M stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines with automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C70F-9510-C stamped on the carburetor air horn, Holley list #3795, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with manual transmissions. *Note - For use with California Thermactor smog equipped cars.

1967 390-4V Holley 4150 carburetor, automatic C6 transmission- California DSO 52 and 53. C70F-9510-D stamped on the carburetor air horn, Holley list #3796, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V or 390GT engines and automatic transmissions. *Note - For use with California Thermactor smog equipped cars.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

Used clip for mounting the vacuum modulator steel line or tube on 1967-68 Mercury Cougar or Ford Mustang with C4 or automatic transmission. Mounts under one of the top bolts where the bell housing connects to the engine block. This is not a reproduced part, that we know of.  The basic Ford part number is 7C072.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Used metal Connector for use on any 1967-68 Mercury Cougar or Ford Mustang with speed control. This connector goes between the Servo and Bell Crank. Connector only, hitch pin and clips not included. Complete Ford part unknown, but it has a basic part number 9D763.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....