1971, 1972, 1973

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Master clip kit which includes the following fasters:Back up light to firewallDoor speakersEngine ffeedRadio cable to dashSide marker and headlightsTaillight wiring and groundUnder dashVarious location zip tiesKeep in mind that not all fasteners found on 1971-73 Cougars / Mustangs are in this kit.

These barrel nuts or clips are exactly like the original ones inserted into the trunk for attaching 1967-68 "Mercury" script, and 1971-72 Mercury Cougar "Mercury" Hood scripts. The manufacturer indicates that these tubular nuts fit 1/8" holes. Pin size on those emblems are 3/32". These clips are also used to attach the 1967 quarter panel emblems. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

Used grade A rocker panel clip for the 71 - 73 Mercury Cougar 

Good used set with no broken studs or missing tension wires on the metal end clips.

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.