All Available Parts - 1968 Mercury Cougar

Core passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. Good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529314-A.

Core driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This is a good trim part that is ready for restoration or could be used on a driver.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit will not interchange with the 1967 tilt / tilt away. This is because the center hole on the 1967 unit is round where this 1968-69 version is elongated. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of...

Used Emergency Flasher Knob Bezel / Fixed Column for the 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang 

NOS passenger side (right hand) rear quarter extension moulding / trim for the Mercury Cougar. These NOS pieces are getting difficult to source. If you have NOS parts, we will buy them!Ford part # C7WY-6529312-A.

NOS driver side (left hand) rear quarter extension moulding / trim for the Mercury Cougar. This piece will show some shelf wear so don't be surprised to find that this piece is not as nice as our restored moulding / trim.Ford part # C7WY-6529313-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

Restored three piece anodized aluminum rear moulding / trim set for the rear of the 67-68 Mercury Cougar. These pieces attach to the rear deck / trunk lid and the quarter extensions. New and used clips also available separately. Ford part #: Driver side quarter extension moulding C7WY-6529313-A, passenger side C7WY-6529314-A, deck lid moulding C7WY-6542512-A. *NOTE* Keep in mind that we do give in-store credit for extra core trim and mouldings you may have laying around (from a Cougar of...

Economy reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible, except for the fact that the clips included have 8mm nuts, unlike the originals. There is however one small problem, the metal on these mouldings is much softer than the originals and you have to take extra care when installing the clips, if you apply too much pressure when installing, you will dimple the...

Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6551728-A.We have found that this 3M product works great for bonding these parts in place permanently....

This is the left hand or "Driver Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529035-A. We have found that this 3M product works great for bonding these parts in place...

These are very correct looking reproductions and sold as a complete set. They do not come with the keepers that go on the backside of the grill, so you will be using common flat washers which actually work just fine. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

Unlike our reproduction rocker mouldings, we can sell these used mouldings individually (shipping is the same price when you buy one or several). Even though there is no difference in fit or part number, we do ask that you choose passenger side or drivers side by mentioning it in the notes as the finish is always duller on the front end, behind the front tires from road debris. The majority of our used 1968 rocker moldings have one screw hole towards the front. Reason being is that there were...

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

THIS KIT HAS A CORE CHARGE OF $950 Here is a time and money saving package deal for the person restoring their 1967 or 1968 Cougar. This package includes: Hood lip moulding Fender extension mouldings Quarter extension mouldings Grille center trim Deck lid moulding Drip rail mouldings Nine piece front and rear window trim Front and rear Award Winning Bumpers All parts are show quality. The bumpers are triple plated chrome, the aluminum has the correct anodized finish just like NOS and the...

This pair of restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part #...

This is the right hand and left hand 1/4 panel moulding. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529034-A & C7WY-6529035-A.We have found that this 3M product works great for bonding these parts...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim splits the lower silver color from the body color. The unit shown is the one you will receive. Near mint, excellent original bright dip finish, an out of package (we still have remnants of the crispy brown FoMoCo wrapper) NOS part with minimal shelf wear. Best you will ever find, ready to put on the car as is. We won't always have this stick of trim in stock, but we will work to accurately...

1968 Mercury Cougar left side or driver rear quarter moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Good used core with a few minimal dings on the raised portion and will easily restore to mint condition. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Passenger and driver sides are contoured differently and are only for the 1967-68 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5387. Shipping will...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1967-68 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5387. Shipping will have...

This restored drip rail moulding / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show car. Ford part # driver side...

This passenger side (right hand) restored drip rail mouldings / trim will have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. Our mouldings / trim are sold outright, as a pair, or one side only. Most people will be satisfied with our used grade "A" drip rail mouldings / trim, however these are for the person that is striving for perfection with his or her show...

Restored trim piece for 67 - 68 Cougars. This is the trim that goes around your driver side quarter window. And since it has been restored, it will be polished to a much higher luster than what the factory would have done.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Restored trim piece for 67 - 68 Cougars. This is the trim that goes around your passenger side quarter window. And since it has been restored, it will be polished to a much higher luster than what the factory would have done.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Used passenger side upper quarter window channel for all 1967-68 Mercury Cougars. This is the stainless steel upper glass frame section only. Our used trim will have some fine scratches or scuffing present. Passenger side only, driver side also available. Restored also avialable. Replaces Ford part number C7WY-6529962-A.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Used driver side upper quarter window channel for all 1967-68 Mercury Cougars. This is the stainless steel upper glass frame section only. Our used trim will have some fine scratches or scuffing present. Driver side only, passenger side also available. Restored also available. Replaces Ford part number C7WY-6529963-A.Check out our video below for helpful tips on disassembling your vent and quarter windows: ...

Used rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

Complete set of seven, extruded aluminum original horizontal GTE grille bar set. Includes all parts in good condition including the four rectangular, notched brackets that attach the center bars from the back side. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

1968 Mercury Cougar right side or passenger door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. The trim pictured is dull, but has no dents or scrapes. Laser straight with only minor scratches and pock marks from road debris on the lower side closest to the fender. We will take used GT-E trim in trade...

1968 Mercury Cougar left side or driver door moulding found on the GT-E models. This unique trim split the lower silver color from the body color. Arrow straight, dull, a couple of minor, very small scratches. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6520939-A.Due to the difficulty...

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit. Original Mercury part number is C7WY-6529035-A with a casting number of C7WB-6529035-D

This listing is for all six pieces restored and of course requires you send your cores in advance. It can take anywhere from 1 to 4 months depending on what time of year it is and where we are in our cycle with our plater as we send a minimum of $20k in at a time. We make sure they are separated from the more common parts we have and these are treated with special care every step of the way. On this particular set we never ask them to hurry. Do know that if you have extra holes drilled they...

1968 Mercury Cougar right or passenger side fender moulding found on the GT-E models. This unique trim split the lower silver color from the body color. This core piece good is for restoration. We won't always have this stick of trim in stock, but we will work to accurately describe the exact piece that we do have in inventory. We will take used GT-E trim in trade towards the reproduction GT-E trim call 503-463-1130 for details.Ford part # C8WY-6516039-A.Due to the difficulty in obtaining trim...

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

This purchase requires you send a good core in advance. If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by...

If your core is not adequate we have cores for sale. Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

If you do not have a core that is worthy of restoration we have them for sale.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

*NOTE* - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC. Why do we require cores be sent for a used piece of trim?We pull the best of our used cores and make them available for those who do not want or need a restored piece of trim, but in order to keep a viable supply of cores to send in to be refurbished we need a restorable core in exchange. If you do not have a core, or wish to send in your core at a later date, we have cores...

*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC. Why do we require cores be sent for a used piece of trim?We pull the best of our used cores and make them available for those who do not want or need a restored piece of trim, but in order to keep a viable supply of cores to send in to be refurbished we need a restorable core in exchange. If you do not have a core, or wish to send in your core at a later date, we have...

*NOTE* - This is a core exchange item only, trim will not ship until your acceptable trunk moulding core is received by WCCC. Why do we require cores be sent for a used piece of trim?We pull the best of our used cores and make them available for those who do not want or need a restored piece of trim, but in order to keep a viable supply of cores to send in to be refurbished we need a restorable core in exchange. If you do not have a core, or wish to send in your core at a later date, we have...

Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. If you are sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital...

Good set of four, used wheel lip mouldings for your 1967 - 1968 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

Core wheel lip mouldings are good for restoration or for a shabby looking driver. They will not be flattened out, ripped, kinked or have salt corrosion.

Core driver side (left hand) front wheel lip moulding / trim for your Mercury Cougar.Ford part # C7WY-16039-A.

Driver side rear wheel lip moulding. This piece is suitable for restoration or could fit right in with a lower quality daily driver.

Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...

NOS driver side (left hand) front wheel lip moulding / trim for your Mercury Cougar.Ford part # C7WY-16039-A.

Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...

Driver side rear wheel lip moulding. Fits any 1967-68 Mercury Cougar except GT-E models.Replaces Ford part number C7WY-6529165-A.

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot that did not come out 100%, a slip on the buffer wheel or a pin hole created by over polishing are what you can expect on a blemished piece of trim. We try to carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to... From 10-15 feet away these will look good...

Used driver side (left hand) fender extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition. Check out all our restored and used mouldings in the "exterior trim" section. Normal 0 false false false EN-US X-NONE X-NONE Ford part # C7WY-16075-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after...

This trim clip is a little larger than the original C4GB-6242364-A retainer assembly Ford used and looks a little different, but will work just fine for the front extension mouldings. This will also suffice as a good substitute for the 46 clips used on the 1968 GTE side moldings. Sold Individually.Length: 13/16" from lip to lip.

Concours quality restored "bright dip" anodized eyebrow moulding / trim for your Mercury Cougar. You do not need to send a core in prior to getting this restored part but we will give you a $10 credit when you send back your restorable core. Like fine jewelry for your beloved Cat!Ford part # C7WY-16075-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you...

Restored passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This is like fine jewelry for your beloved Cat!Ford part # C7WY-16076-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Keep in mind we buy most trim and mouldings found on a...

Restored driver side (left hand) center grill moulding / trim for the Mercury Cougar. No core needed for this purchase. Looks better than NOS! Ford part # C7WY-8A157-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Keep in mind we buy most trim and mouldings found on a...

Restored passenger side (right hand) center grill moulding / trim for the Mercury Cougar. As you can tell, price wise, you are much better off to purchase the entire set together as opposed to one at a time.Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Restored passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. They really do look as good in person as in this photo. Due to the "enclosed" nature of this design only cores with minor dings can be restored. Ford part # C7WY-16856-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you...

Restored hood lip moulding / trim for the Mercury Cougar. They really do look as good in person as in this photo. Due to the "enclosed" nature of this design, only trim with minor dings can be restored. Ford part # C7WY-16855-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Used driver side (left hand) center grill moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-8A157-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you...

Used passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-8A158-A. *NOTE* This unit carries a $20 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for...

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. Ford part # C7WY-16076-A. *NOTE* This unit carries a $30 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option...

Core anodized aluminum front moulding / trim set for the Mercury Cougar. This is a six piece core set of front mouldings with minor dings and scratches. Good for a poor quality driver or for restoration.  Parts will have no holes, cracks, or heavy pitting.  If you are wanting our six piece restored set and do not have a set to exchange, this listing is what you will need to purchase in conjunction with the restored set.

Core driver side (left hand) center grill moulding / trim for the Mercury Cougar. Good used core that will have minor dings, dullness, and scratches. Ford part # C7WY-8A157-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Core passenger side (right hand) center grill moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness. Ford part # C7WY-8A158-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Core driver side (left hand) fender extension moulding / trim for the Mercury Cougar. This is a great option for those of you who like to save money by restoring your own parts.Ford part # C7WY-16075-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Core passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16076-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. Also, the tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16074-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side (right hand) center grill moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. Also, the tooling was typically near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim. Ford part # C7WY-8A156-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Do you want to replace those worn out actuators yourself or are you looking for some...

NOS driver side (left hand) hood lip moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear and often the tooling was near the end of its life so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16855-A

NOS driver side (left hand) center grill moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was also typically near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim. Ford part # C7WY-8A157-A. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. Do you want to replace those worn out actuators yourself or are you looking for some great...

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

Restored six piece anodized aluminum front moulding / trim set for the Mercury Cougar. We suggest you make the order online and then send your cores with a copy of your invoice. Once your cores arrive we will ship the restored set.  If you do not have good cores we do have them for sale. These restored original trim parts have the correct satin "bright dip" anodized finish and look like NOS! We have sold hundreds of these trim parts to Cougar owners all over the world, many of which are...

Used passenger side (right hand) upper rear window moulding / trim for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42430-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Used driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same piece as the 1969-70 piece, however those pieces carry a part number beginning in C9WY. Ford part # C7WY-42405-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Also,...

This rear window moulding set has been restored to show quality. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY. Ford part #'s: Driver side upper C7WY-42431-A, driver side lower C7WY-42405-A, passenger side upper C7WY-42430-A, passenger side lower C7WY-42404-A. *NOTE* This unit carries a $200 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit...

Restored driver side (left hand) upper rear window moulding for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42431-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Also, keep...

Restored passenger side (right hand) upper rear window moulding / trim for the Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42430-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Restored driver side (left hand) lower rear window moulding / trim for the Mercury Cougar. This is the same part as the 1969-70 piece, however those pieces will carry a part number beginning in C9WY.Ford part # C7WY-42405-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim...

Restored passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42404-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Used drive side (left hand) upper rear window moulding / trim for the Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42431-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section. Also, keep...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529034-A

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider installing your dash...

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent as shown here. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider...

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

This 2 1/4" trim part installs directly above the steering column.

Only for use on standard model Cougars with AC. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Show-quality triple chrome plated passenger side quarter window frame for 1967-68 Cougars. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait until you receive your restored pieces to get reimbursed. Note: Badly pitted window frames may not be restorable, as the pits will need to be sanded out. If they are too deep, they may leave...

Complete kit with 12 white plastic mounting clips, 2 black plastic mounting brackets that attach rocker mouldings to scoops, 2 aluminum rocker mouldings and 2 chrome plated scoops.  Due to supplier shortage, the metal rocker panel clips are not available at this time. Click Here to View Installation Instructions   These are correct for 1969 only but can be used on any year 1967-1973                   ...

Reproduction rocker moulding / trim end clip for the Mercury Cougar. This clip is a steel clip with a wire like the original. These units are technically for the 1969 and 1970 Cougar, but they will also work well with the 1968 rocker moulding / trim. Four of these clips were used on all 1969 Cougars except for the Sport Special which used two. The 1970 Cougar also uses two per car. Sold individually.Will work on 71-3 with modification. ...

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Used in 1968 Mercury Cougars for the sequential motor, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending unit in the fuel tank. ...