Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...
Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!
Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
New screw with a correct 3/8 inch hex head for installing all armrests for all years.
part # 382101-S2 Sold individually
part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"
Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.
12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
part # C1AE-6065-C. Shorter of two. Sold individually
part # C1AE-6065-A. Longer of two. Sold individually
Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.
Bolt with toothed washer for attaching 1967-68 Mercury Cougar and Ford Mustang door window parts. Both of the door window rear stops
373460-S Factory original used bolt used to fasten the guide to the door (2)
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length. Replaces Ford part # 380288-S. ...
Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.
Replaces Ford part # 385664-S
Replaces Ford part #375381-S Phosphate & Oil Finish
part # 379068-SSold individually
Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.
Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.
Front U clamp sway bar bracket bolt, for any 1967-68 Mercury Cougar or Ford Mustang. 3/8-16 x 1.0 Grade 5 bolt. Sold individually, 4 per car. part #20408-S
part# 20352-S Sold individually
Reproduction intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with either the 390 or 428 engine. These little units are sold individually.
Reproduction caliper bolt from AMK Grade 8 hex bolt. 2 bolts per caliper, sold individually. 7/16-14 x 1-5/8". These bolts hold the two halves together on the four piston Kelsey-Hayes calipers. Fits Kelsey-Hayes installed, 4 piston disc brake calipers used by Ford 1966-67.Replaces Ford part # 378225-S.
Plain head, fine thread. Not concours, but meets or exceeds original specs. Sold individually.Ford part # 380328-S.
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used to mount the vacuum actuator to the column in 1967 and the actuator to the bracket on 68-69. Also used to mount the steering column relay and vacuum release valve in 1968-69.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last...
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block. Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)
replaces Ford part # B-12764
Rear valance and 1967-70 windshield defroster attaching hardware. Sold individually. Zinc (dark silver)
Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.
Front inner bolt that attaches female portion of the lap belt to the transmission tunnel. Used in conjunction with a silver, fat washer that is slightly cupped.
Used early version of the long seat belt bolt for the Mercury Cougar or Ford Mustang. This early version has faint markings on the head of the bolt as where the later versions have more prominent markings. 13/16" hex head, two inch bolt with a 1/2 inch shoulder. Can be either smooth headed or have an "E".
Used early version short seat belt mounting bolt to mount the front retractor to the inner rocker panel and used in conjunction with a large washer. This is an early version of the the seat belt bolt with faint or no markings on the head, the later versions are longer, and have much more prominent head markings.13/16" hex head, 1-1/8inch bolt with a 3/16 inch shoulder.
Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".
12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.
Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads
Replaces Ford part # 45964-S Sold individually
Reproduction steering gear box bolt. Sold individually