Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.
Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.
Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.
Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...
These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...
Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.
Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.
Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.
NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B
Driver side vertical windshield moulding. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part number C5ZZ-6503137-B.
Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.
Core passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503144-B.
Core passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503136-B.
NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.
This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar. These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore" mouldings that are available as they...
Bolt that goes through the air pump mounting bracket. Pump rotates on this bolt. Bolt size 3/8"-16 x 4.25" long.
This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.
These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...
Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...
Plate for mounting the spare tire. 4 inches outside diameter with the 3 tabs.
CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber
Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.
Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.
New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.
O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.
OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang
Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This black painted push on oil cap was on California sold cars with closed emissions systems. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a chromed version was also available with engine dress up kits.
Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was used on the DGS package or engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California. This icon means that we're looking to buy...
Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...
Precision machined to the factory specifications. Light gold anodize finish just like the original.
Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.
This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.
The oil filter made by the original Ford supplier.
Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.
Includes drain plug.
Used oil screen pick up tube assembly from a FE or big block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...
Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Base standard saddle arm rest on a 1967 Mercury Cougar or Ford Mustang, interior trim code 2F. Nothing matches the fit and feel of NOS. This will outlast the reproduction armrest three to one. Ford part number C7ZZ-6524140-A1F.
Reproduction disc brake pedal pad for the 1967 Mercury Cougar or 1965-67 Ford Mustang equipped with the automatic transmission. This is identical to the 1968-73 pad, just slightly narrower. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part # C5ZZ-2454-C.
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.
New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons
Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions.
Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.
Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.
Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.
Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.