1972 Mercury Cougar

Used replacement toggle switch for the 71-73 Cougar XR7. This is a single throw switch that can be used in either the map or courtesy light positions on the switch assembly.

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

Sold individually Zinc (dark silver)

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

Manufacturer calls this a torque pin kit, it consists of 3 pins. Pin diameter is 1/2 inch and are 13/32 inches long. Made from natural nylon. Fits most Ford vehicles with power windows from 1964 - 1973+.

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1971-73 Mercury Cougar torsion springs D1WY-6544890-A and D1WY-44891-A. The body section of the shop manuals describe how to adjust these bars, we offer a torsion...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

Core C6 transmission for a 1972 Mercury Cougar or Ford Mustang, with H code 351-2V engine. Tag number PGA-AV1 or PGA-BA. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1972 Mercury Cougar with 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1972 Mercury Cougar, with Q code 351CJ or 351-4V engine. Tag number PGA-AH1 or PGA-AH2. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1972 Mercury Cougar with 351CJ engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person. * Note - 1972 and 1973 Mercury Cougar could be either...

Core C6 transmission for a 1972 Mercury Cougar or Ford Mustang, with Q code 351CJ or 351-4V engine. Tag number PGA-AU1 or PGA-AU2. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1972 Mercury Cougar with 351CJ engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person. * Note - 1972 and 1973 Mercury Cougar...

Core FMX transmission for a 1972 Mercury Cougar or Ford Mustang. Tag number PHB-E4, PHB-E5, or   PHB-E6. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1972 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Outer casing for the C6 transmission on the 71 - 73 Cougar or Mustang. Case only, does not include any of the inner workings or output shaft.

Reproduction transmission cooling lines made from OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351 engine.

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Used transmission tunnel specialty cut. From a 1971-73 Mercury Cougar.File picture of 1967 tunnel, you get a 1971-73 tunnel cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe or convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545119-A.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe and convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545118-A.

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...

Reproduction heater core tube gasket for the 1971 - 1973 Cougar or Mustang. Never sold as a service part by Ford, this gasket seals the area around the heater core tubes where they pass through the vehicle's firewall. The gasket is cut from closed cell EPDM foam sponge rubber that matches the original material used by Ford. Designed to withstand the temperatures found under the hood and surrounding the heater core tubes. ...

Used turn signal flasher for the 1972 Mercury Cougar Ford Part number D2AB-13350-A or D2AB-13350-AA

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. NOTE* Some vehicles have the wiring reversed, you can get though this problem by using spades and hooking up to the contacts of the flasher backwards.  This is the updated flasher unit for use with the updated sequential unit and...

When your lights are sequencing too rapidly, causing the outer light to not fully illuminate, your original unit is most likely the culprit. This solid state unit replaces the small red (69-70) or green (71-73) flasher found under the dash, next to the radio. Replaces Ford part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

9" inside the arch to the end of the threads. Thread size 7/16-20, includes tall nuts as shown. Concours Grade 5 flange nuts available separately, see related items.

Leaf Spring U Bolt for the 1967 - 1973 Mercury Cougars with isolators. Will work on any 67-73 Cougar. Does not feature flattened area at top like original. Includes 1 'U' bolt and 2 nuts. 4 total U-bolts needed per car.  *Note - For use with Cougar shock plate, angled wedge, rubber isolators and retainer boxes. Inside Height:   6-3/4"Inside width:   2 7/8"  (Same as axle tubes) Replaces Ford Part #: C7WY-5705-A. ...

This would be for the non-competition suspension Cougars. U-Bolt length 6-3/4 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts. Competition suspension U-Bolts run about 7 inches in length. Ford part number C7WY-5705-A for Competition Handling option.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.