1972 Mercury Cougar

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

"A" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. Hard to find them without broken mounting tabs. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

1971-72 Mercury Cougar convertible driver side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting # D1WB-7628519, Mercury MPC # D1WY-7628011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

1971-72 Mercury Cougar convertible passenger side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting number D1WB-7628518, Mercury MPC number D1WY-7628010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used driver side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A" panels, due to...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form, and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used passenger (right hand) side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A"...

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area

Good reproduction made in Taiwan. Much higher quality than the Chinese version of this regulator. Replaces Ford Part #: D1ZZ-6523207-A Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with power windows. *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion is about 24 inches long.  Replaces Ford part number D0OB-8B170-B.

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford part # D2ZA-19A242. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Mercury Cougar and Ford Mustang factory AM/FM stereo. Good used working stereo, but the knobs are sold separately. Ford part # D2ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Mid late 1972 Mercury Cougar, approximate starting is 3-1-1972 through 1973. D2WY-6540110-A style has the style of keeper for the deck / trunk lock cylinder that pushes up through a rectangular access hole in the bottom. These deck / trunk lids have a rectangular access hole under the trunk lock with a single rivet or screw hole. For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden...

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar convertible. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610125-B.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610124-B.* Note - this item has dimensions in excess of 75 inches, and will...

This panel was used on all convertible models without retractable rear belts. Please contact us for choice of color, power or manual windows and with or without seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.