1972 Mercury Cougar

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

Used grade "A" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This very clean uncut harness is not corroded on the connections or brittle from heat is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7...

Used grade "B" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This harness may have one or two professional repairs, it is tested and ready to install. We also have this harness in grade "A" condition for those of you who must simple have the best original parts money can buy.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash...

Used grade "A" under dash wiring harness with fuse panel / block for the Mercury Cougar XR7 and XR7 convertible. This very clean uncut harness is not corroded on the connections or brittle from heat is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7 harness.Ford...

Used grade "B" under dash wiring harness with fuse panel / block for the Mercury Cougar XR7 and XR7 convertible. This harness may have one or two professional repairs, it is tested and ready to install. We also offer this harness in grade "A" condition for those of you who simply must have the finest original parts money can buy.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses....

Just about the only possible reason to put this poor quality reproduction on your Cougar is that it is a good tool to put out engine fires. No Joke! If you happen to have an engine fire you can carefully open your hood, yank the blanket downward and smother the fire by pushing the blanket tight around the area that is burning. This can at least buy you time until a fire extinguisher is located. How do I know? I saved a very pristine 1974 XR7 a few years ago this way! This inexpensive product...

Used standard grade "A" main under hood wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1972 Mercury Cougar Standard models only (after 12/1/1971) with AMP warning light. Not...

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1972 Mercury Cougar Standard models only (before 12/1/1971) with AMP warning light. Not...

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1972 Mercury Cougar Standard models only (after 12/1/1971) with AMP warning light. Not...

Used XR7 grade "B" main headlight wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1972 Mercury Cougar XR7 models (before 12/1/1971) only. Not compatible with Standard model Cougar...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

All applications, attaches the drive shaft U-Joint to rear end pinion yoke. Sold in pairs, complete with nuts. Perfect used. Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

NOS upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1969-70 Mercury Cougar or Ford Mustang. Ford part number C9ZZ-7521-A.

NOS upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Nice quality reproduction of the upper clutch rod that connects the clutch pedal and the Z-bar on any 3 or 4 speed manual transmission in a 1971-73 Mercury Cougar or Ford Mustang. Has the correct length, critical measurements, and contours. Ford part number D1ZZ-7521-B.

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

New quality upper control arm shaft kit. Fits all 1967-73 Mercury Cougar and Ford Mustang, also Maverick/Comet 1970-77, Fairlane 1966-70, Torino/Cyclone 1968-71. Comes with all parts shown. This is a much better design than the original Ford design. The down fall is it does not look at all like the original Ford kit. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. All bare sheet metal steel construction starting in 1971 until 1973. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port on the side.

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number D0AE-A casting.This casting number is correct for all 1970 1971 1972 and 1973 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy...

New Old Stock Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on select Ford models. This is a NOS original electrical and vacuum operated switch. It has the FORD oval logo and part number D1AE-AA casting. This casting number is correct for select 1971 and 1972 Fords and Mercury. It was used on 302 351C and 351W engines. Because of the heavy demand placed on the cooling system by the factory air option this was mounted...

Over 100 total vacuum caps in 6 different sizes.

Saves time and frustration! Shows schematic and diagrams that reveal the location and function of the many vacuum systems on Cougar's.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used vacuum switching manifold and electrical micro switch assembly from a mid to late 1972 through 1973 Mercury Cougar and Ford Mustang. This is the plastic version with riveted micro switch. We test the micro switches prior to shipping. Please check your A/C controller to verify that you have and need the plastic version of this switch. We also have the all metal version with separate micro switch which can be interchanged, but you would need a micro switch.Ford number D2ZA-19B919-A or...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Core small block C6 Transmission valve body for any 1971-73 Mercury Cougar or 1971-73 Ford Mustang with code "U" transmission code on the door tag and either "M" or "Q" code 351-4V or 351CJ engines. This is only for 1971 or 1973 transmissions with P-R-N-D-2-1 shift pattern, floor shift. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch...

Core FMX Transmission valve body for any 1972-73 Mercury Cougar or 1972-73 Ford Mustang with code "X" transmission code on the door tag. This is only for 1972 or 1973 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.