1973 Ford Mustang

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Used retaining bolt with nut for the fixed column on any 70 - 73 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

This used retaining clip was originally used to connect the two power steering hoses together at the power steering box. Used on all 1971-73 Mercury Cougar and Ford Mustang with power steering and V8 engines. Ford shows this item in the chassis assembly manuals and it is called a hose retaining clip, and the Ford part number is D1ZA-3E506-AC.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

Great reproduction of a rather hard to find part.

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Automatic transmission kickdown control retracting spring. 1971-73 Mercury Cougar and full sized Ford/Mercury, mid sized Ford/Mercury, Ford Mustang, Maverick/Comet, and Thunderbird/Lincolns. V8 engines only. Replaces Ford Part #: D1AZ-7B146-A

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

Power Steering Hose Manufactured in the U.S.A. Low pressure return hose.  Replaces Ford Part # d1zz-3a713-a

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim.  Cast...

Reproduction quarter window roller for the 71 - 73 Cougar or Mustang. These rollers attach to the window channel bracket and slide up and down through the window guide.Sold individually

Quarter window guide roller with swivel head for all 1971-73 Mercury Cougar or Ford Mustang Coupe or Convertible. Three of these rollers per side

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car.Replaces Ford part # D1ZZ-6522244. Sold individually

Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This is the type of material that was used to install gasketless windshields starting in 1969. Tom

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

D3ZZ-4730-A Rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1973 Mercury Cougar and Ford Mustangs. Good used part with solidly mounted metal threaded stud. Pinion bumper.

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Sold individually. Zinc (dark silver)

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Special Phillips pan head screw for attaching the pancake motor to the quarter window regulator. 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Weird threaded screw, called a triangle threaded screw. Slightly larger than 1/4-20. Unique and limited to quantity on hand. Three screws per regulator, sold individually. Ford part # 381530-S. *NOTE* For those of you who like to rebuild and refurbish your own parts, check out our video below. It will take you through the pancake motor...

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used unique Phillips bright finish screw that attaches cable guides to roof.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out our video on rebuilding your shifter below: ...

Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.

Mounts inside the trunk of both coupes and convertibles. Replaces Ford part # D1ZZ-9008.