Body

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields, but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16103-B.

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16102-B.

Reproduction rear taillight panel lower structure / support for the 67 - 68 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, cable and hardware, NOS Ford. Detailed instructions included. Latch not included with this kit. Sorry, the way it came. This kit was a dealer sold kit or over the counter kit. Fits a large range of Ford cars. Ford part number C4AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to...

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade A's will have no scratches or dings.Ford part number C8ZZ-17B719-A

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade B's will have minor scratches or dings. Ford part number C8ZZ-17B719-A

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

Good used center reinforcement beam, or structural brace section for the roof skin. It does not actually attach to the roof skin. Attaches to unitized structure of the roof frame sides. Ford part number is 50222, or 6550244.

In the past, you would have had to purchase a used roof cut from a parts car which meant that you would most likely have do a bit of work to get it straight and clean enough for paint. But now our friends over at Dynacorn have finally come through with a quality reproduction roof panel skin for the 1967-68 Mercury Cougar. If you need a partial roof we can cut this part down to your specifications with a plasma cutter. The price will remain the same but if you need only a half of a roof you...

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Good used jack with correct fine threads. Notice the remnants of the original jack instruction decal. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not.Grade B will have Rust and or the top portion letter "M" fitting may be damaged.

Sold Individually. Chrome plated oval head screw to hold door sill plates in position. Two sill plates require 18 screws - available as a screw kit - Best value! Replaces Ford Part # 376290.

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

One kit does both rear armrests for the XR7 or Standard interior coupe.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Fits all Mustangs

Sold in a set of 18 Replaces Ford # 376290

These reproduction quarter panel end seal screws fit both the Standard and XR7.

These reproduction fender shield to bumper screws fit bot the standard and XR7.

Here are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Seals between chrome vent frames and door on exterior side. Stops water from leaking between vent window and door. Keep in mind that this seal comes as one strip and it meant to be cut down the middle.Sold as a pair.Replaces Ford part #: C6OZ-6322280 or C6OZ-63222A80-A.

These high quality vent window seals are the first on the market to replace the original Ford part exactly. This is the small seal at the front of the door and next to the door weatherstrip. Sold as a pair. Replaces Ford Part #:C7ZZ-6522332/3

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...