Body

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

This seat riser / platform is specific to Mustang, but if you're "vertically challenged"....you may want to go ahead and use this part on your Cougar. It'll raise your seat up enough so that you don't have to use phone books anymore!

Here is our free download for the 1968 Mercury Cougar sunroof panel service procedures.

Reproduction shock support for the 67 - 68 Cougar. This support sits underneath the transition hump and attaches the upper mounts of each rear shock. The shock hardware is accessible through two access holes on the hump.

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...

We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. If you are replacing two towers because of cracks, we strongly suggest upgrading to a 1969-70 pair of reinforced towers. The 69 and 70 towers are an exact fit into your 1967-68 Ford Mustang or Mercury Cougar. There are no specific part numbers for this structural front suspension section.Generic Ford part #s C7ZZ-16054-C or C7ZZ-16054-E, includes apron and side member. Here's a little film to help you fortify your flexxy feline! ...

Used driver side shock tower and apron assembly for the Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Used passenger side shock tower and apron assembly for the Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Solid, undamaged driver and passenger side shock tower braces. Fits all 1967-68 Mercury Cougar and Ford Mustang. Ford part #s C5ZZ-16A053-B driver side (left hand) and C5ZZ-16A052-C passenger side (right hand). *NOTE* Excludes 1967-68 Mustang Convertible. **Installation Tip** These brackets attach under the cowl lip. ...

Shock tower coil spring cover installation hardware that fits Cougar and Mustang coupe, fastback and convertible.

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

Reproduction passenger side (right hand) floor pan cowl side panel for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your car!

Fantastic quality in all respects, concours quality. Don't forget to select a mounting gasket and mounting kit if needed. Replaces Ford part # C7WY-17696-A.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Working driver side (left hand) grade "B" remote mirror with dull chrome. Don't have too high of expectation on this, it is 40 years old and comes from a car we most likely pulled from a brier patch...

Reproduction driver side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967-68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be...   This product has been getting great reviews in the Cougar...

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967 - 68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be... This product has been getting great reviews in the Cougar...

Reproduction convex passenger side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Dimensionally correct reproduction that will allow you to use an original XR7-G remote mirror or the manual mirror found on the Hurst Oldsmobile or AMC Rambler Scrambler. Do you have riv-nut questions? Here are riv-nut answers!

This driver side (left hand) remote mirror was used only on the 1968 XR7-G Cougar and is a direct bolt on for any 1967-68 Cougar and uses the same mirror base gasket. It comes ready to install with the exception of correct adapter base that we sell separate. The casting and chrome are good quality here, the only thing we find issue with is the quality of the mirror lens and the fact that the lens is rather loose in its setting. It does hold its position well as you drive down the road. Do you...

Good used external XR7-G driver side (left hand) rear view mirror with its adapter base, lens, and cables all in good used condition.  Do you have riv-nut questions? Here are riv-nut answers!

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

This unique little adapter was used on XR7G models equipped with a sunroof. This reproduction is bare metal and will not be wrapped in leather like the originals.

This unique little adapter was used on XR7G models equipped with a sunroof. Hand wrapped in the same leather as your center console.

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

The four part, die cast vinyl top trim kit requires 17 (right rear under back glass is the odd ball that requires five fasteners) of these speed nut fasteners. These do not work in conjunction with the various dealer installed aluminum vinyl top mouldings. *NOTE* The factory nuts had a drop of silicone or trim adhesive inside the bowl that acted as a seal. This procedure is advised for reinstallation.

Finally, correct Cougar splash shields! For years, all we had were the Mustang versions that didn't fit right. These are contoured just like the originals to fit your Cougar's fenders. Made from a nice reinforced rubber compound, these are great replacements for your cracked, broken originals. Salvage your original metal brackets and attach these new seals. 1967 and 1968 are different. Staples included.

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. A lower front chin spoiler / air dam was never an option for the 1967-68...

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

This spring has two functions. The first is to connect the rod that opens the latch to the deck lock cylinder. The second is to put tension on the cylinder so as to return the key to its perpendicular resting place after unlocking the deck lid.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Used pair of diagonal support / stabilizing brackets for the 67 - 68 Cougar. The bars are located behind your back seat and help with stabilizing the car and to prevent the body from torquing or twisting. For added support we recommend installing our seat divider panel. These brackets will be cut out of a scrap car and sent to you as is and will need to be trimmed and cleaned up for paint. Check out our video on front suspension and chassis upgrades below: ...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.