Body

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Complete reproduction trunk floor pan for the 67 - 68 Cougar. Also includes rear shock support, axle bumper mount, and rubber plugs for the shock holes. When ordering this item, keep in mind that it is an over-sized box which will be drop shipped from our supplier in California or available for in store pick up at WCCC. You can expect to pay up to a few hundred dollars for shipping (oversized items must be truck freighted). Often, all you need is the left or right trunk sections. You can save...

Complete non assembled trunk pan kit. Included are the transition panel, trunk floors, rear taillight support and shock support. This kit will require you to assemble and weld in all individual pieces of the rear trunk pan on your own.  This is an oversized box, so expect to pay about $300 for shipping, depending on location.

Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

Good used, rust free valance that will need minimal clean up before painting. These are not paint ready flawless parts, but rather 40 years old and taken from a parts car. Our reproduction front valances are spot on perfect so if you are not set on OEM please do look at them here, as they are a very good value.Ford part # C7WY-17620-A.

This is a reproduction front valance for your Mercury Cougar. This valance is an excellent reproduction in every detail. Below are pictures of it next to a NOS valance for comparison sake. As you will see, this is an "A" class reproduction in every aspect. Rarely is a reproduction ever a match in any way to NOS. This one is an exception to the rule!Click on images to enlarge. The fasteners for the license plate are just slightly different but the function and placement are dead on.  These...

These reproduction valances have been modified and fitted with high quality reproduction XR7G fog light buckets. When you compare an original valance to these you will see much more care was given than in the originals when placing the buckets. These will require minimal finish work where the buckets were welded to the valance. This is a limited production run only available from WCCC.Replaces Ford part number C8WY-17620

Very Limited supply. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.

THERE ARE NO RETURNS ON THIS PART. Not a good fit but you can make them work...You will have to elongate a couple of the small holes that mount the valance under the bumper, but not by much. Once mounted the part looks as though it was not made quite wide enough. We recommend purchasing our premium version, because honestly, you'll spend a lot of time trying to get this offshore reproduction to fit right.  Please do not call us and say you are disappointed with this part; we are telling...

Premium reproduction rear valance for the 67 - 68 Cougar. This valance is a direct fit, as opposed to our economy version which take a bit of modifying just to be installed and will never look like if really fits right. This premium valance is very durable weighing in at 5.12 pounds, compared to an original which weighs 4.11 pounds. Replaces Ford part # C7WY-65405144-A. ...

Reproduction XR7G rear valance. Our supplier takes premium rear valances and meticulously cuts out the correct pattern and installs reproduction exhaust trim rings.  Replaces Ford part # C7WY-6540544-A.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

New old stock passenger side vent window handle for any 1968 Mercury Cougar or Ford Mustang.  Drive pins and washers included.Ford part number C8OZ-5422916-B.

Pressure die cast in zinc and heavily chrome plated. Excellent quality. Drive pins and washers included, sold as a pair.

Reproduction black vinyl top that looks good and fits perfect. This top has the correct pattern, however the finish is a bit shiny and will not look original to the discriminating eye. Also, the backing is a white felt material which is prone to trapping moisture and causing your roof to rust. The original tops had a more durable canvas-like backing. This top will also have a seam in the A pillar. If you're doing a high quality restoration, we recommend our Concours vinyl tops. Check out...

High quality reproduction black vinyl top for the Mercury Cougar equipped with a factory sunroof that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Thinking about installing this unit yourself? Check out our video below for some inspiration. Below are...

High quality reproduction white vinyl top for the Mercury Cougar that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Please allow 2 - 3 weeks for delivery. Thinking about installing this unit yourself? Check out our video below for some inspiration....

High quality reproduction white vinyl top for the Mercury Cougar equipped with a factory sunroof that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Thinking about installing this unit yourself? Check out our video below for some inspiration. Below are...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Sold as a pair, includes plastic fasteners. There are multiple manufacturers of this particular item and we feel after using them all on our own cars that we carry the best out there. Replaces Ford part #C7ZZ-6520530-A.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety.*Customer Feedback*"I know Don Rush is a trusted and well respected guy. I would just like to give my opinion of him and his team from a Cougar owner in the UK. On one end of the spectrum you have the low lives such as XXX XXXXX who will scam you at the drop of a hat. At completely the opposite end you...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.Used inner and outer passenger side (right hand) wheel house...

Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...

Good used trim part that helps hold the rear panels in place. It is known as windlace or pinch weld moulding. There are two types of this trim found in the 1967-68, the rough or smooth textured version as shown. Please enter your desired color and texture into the comments section.

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...

Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.

This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Spare Tire Mount Wing Nut Reproduction for the 1968 through 1973 Mercury Cougar / Ford Mustang

For 1968 Ford standardized or changed all of the J-bolt threads to the beefier 1/2"-13. We have noted two variations of this wing nut. The most obvious identifier between the two is the tabs in the center. The majority have these tabs present, the minority do not. We also stock and carry the correct disc or hold down plate, and the J bolt. Lots of sizes and lengths for those. Do you have the correct one?

Same harness works for driver or passenger side, sold individually.

Used under dash wiring harness repair plug and pigtail for the door ajar / seat belt warning for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

[No Description Provided]