Body

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16054-A, included apron and side member. ...

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustang. Consider our brace kits for the best bang for your hard earned buck! Ford part # C9ZZ-16A052-A. *NOTE* Excludes 1969-70 Boss 429.

Reproduction shock tower brace nuts and bolts for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Used, solid, and undamaged shock tower braces for all 1969-70 Mercury Cougar and most Ford Mustangs. Includes 4 used 7/16"-14 x 1-1/4 inch cowl attaching bolts. Ford part #s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand).  *NOTE* Excludes 1969-70 Boss 429. **Installation Tip** These brackets attach 'under' the cowl lip. Here's our little film to help you fortify your flexxy feline! ...

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

Reproduction driver side (left hand) remote sport mirror for the Mercury Cougar XR7. This unit will come with a primered base and head so that you can paint it to match the rest of your car. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find! 1970 was the first year you could get a factory installed sport mirror on your XR7, Sports Special, or Eliminator. If you would also like to have a...

If your mirror is fine except a broken off wand (control lever) it is an easy fix. Since the wand is made of a soft metal it is not too hard to drill out the old and replace it with one of our threaded replacement units. One can also remove the entire adjuster assembly form another mirror that has a broken base and carefully attach it. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find. Have...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road?...

Used passenger side (right hand) sport mirror for the Mercury Cougar Eliminator. The Ford service replacement part number for the complete assembly is DOOZ-17682-D with a casting # on the base that reads D0OB-17713-AW. This is the correct right hand mirror for your 1970 Eliminator. It was available over the Ford counter to be placed on any 1969-70 Cougar but the 1970 Eliminator is the only model that came from the factory with it. Unlike the driver side door there is no factory embossed area...

Reproduction passenger side (right hand) manually adjusted sport mirror for the Mercury Cougar or 1970-1971 Ford Torino / Cobra / Ranchero / Cyclone. Our kit includes everything needed to mount a bullet style sport mirror to the passenger side of your vehicle. This reproduction unit is far more durable than the originals which were cast with a softer metal. The Ford service replacement part number for the original complete assembly was D0OZ-17682-D. The base in...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

If what you are looking for is a sound deadener kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give you an honest idea of what you are...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Original space saver tire marked B.F. Goodrich F78-14. Display only, it can not be inflated. Rear side wall has damage. From a 1970-71 Mercury or Ford. Bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? Has the good tread design, single fill valve stem, but with damaged sidewall. This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is a...

Original space saver tire marked F78-14 B.F. Goodrich, from a 1970's Mercury or Ford. These were optional in 1968-73. It has the smaller hub size and single valve stem. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire. *NOTE* Does not include inflator bottle and valve caps are usually missing. ...

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

Reproduction original style chin spoiler. Nice quality, fit and finish. Made from thin plastic just like the originals. Comes as bare black plastic, so we suggest coating with your favorite semi-gloss black paint for a more finished look. Take a look at the 1:33:00 mark in the video below to see how we compare the reproduction to the original: ...

DROP SHIP ETA - 4 WEEKSUnbelievable, truly authentic concours restoration quality reproduction spoiler kit includes the wing blade constructed of an ABS based thermoplastic and is molded in gray (as original). It's not fiberglass. This two-piece wing (as original) derives its rigid stability from the material itself (as original) instead of some secondary internal support such as a metal rod or foam. And it's not light weight, it's the right weight... at over 8 lbs.! All dimensions are...

Show quality, correct weight and markings. Sold individually.

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Hood hinge spring specific to the 1970 Mercury Cougar. Total spring length 4-55/64" long, coil spring thickness is 0.222", and the coil diameter is 2.181 inches. 1970 spring is shown on the right side in the inset picture comparison. Stronger hood spring to compensate for the extra weight of the 1970 hood extension. One year spring. Springs sold individually, one per side.Ford par # D0WY-16789-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find any rust (other than surface) and no signs of excessive filler. We have...

Reproduction rear deck spoiler stripe in black for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.Also sold in a complete kit.

Reproduction rear deck spoiler stripe in white for the 1970 Mercury Cougar Eliminator. We reproduced these stripes from a NOS kit, and they are the most correct Eliminator stripes on the market today. Cut from the same 3M vinyl as original.

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

This kit mounts the spoiler pedestals to the trunk lid. Studs measure 2-3/4" long, correct for the Concours correct stands.Some economy or generic kits come with 1-1/2" studs

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.