Body

Backer boards are not perfect but very serviceable with only a couple broken clip cutouts, NO cracked pillows, The passenger side has one very small knick in the vinyl and has white overspray in places which can be removed with "Goo-Off". We suggest not worrying about removing the overspray and give the panels a fresh look by applying 2 coats of SEM Landau black flexible coating. These will also need a pair of our black reproduction armrest escutcheons. This icon means that we're looking to...

Very rare to find NOS these days! Very limited supply...Add Ford part Number C9LY-6522666-A2A

Very rare to find NOS these days! Very limited supply...Keep in mind that the 1970 XR7 Green is a slightly lighter green than in the 69. 

Very rare to find NOS these days! Very limited supply...

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners. When you turn it over and inspect it, the seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, no excuses, satisfaction guaranteed....

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 69-70 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners. When you turn it over and inspect it, the seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, no excuses, satisfaction guaranteed....

D0WB-13A769-A Right side door wiring harness that includes door ajar and courtesy lights. Found on 1970 XR7's and 1970 Standard Cougar with the Safety Convenience Package. D0WB-13A769-A is the tag number originally found on the harness. Wiring harness for door ajar and courtesy light. Master part number D0WY-13A769-A. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

This restored passenger side (right hand) drip rail moulding / trim has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail mouldings / trim. The vinyl top...

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim have had all minor dings and scratches removed and then polished to a mirror like finish. These mouldings have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail...

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP125 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Ford part # D0WB-16018. Mercury MPC # D0WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A

Used driver side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Unlike the parts pictured, we only have pitted covers left. At present we have no grade "A" examples. C8MB-5422678-A. Brushed die-cast (with stainless steel look) cover for the chromed grab handle end part number C9MB-5422668-A. These are the smooth or plain ends, the Lincolns used a cover that had scrolling. Used on 1969-70 Mercury Cougar XR7 and various other Lincolns and Mercury full sized cars. These clean up pretty well with steel wool as shown. Keep in mind we have reduced priced...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

THE QUALITY ON THESE HOOD SCOOPS HAS DECLINED GREATLY, AS OF NOW WE WILL MOST LIKELY NOT BE ORDEREING ANY MORE UNTIL THE ISSUES ARE CORRECTED. Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This...

BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The Scoop measures 21 5/8" at the widest point on the front, 25" at the widest point at the rear and 26 1/8" tall when stood on end and measured at its longest point. The scoop is 2 7/8" tall at the front middle when mounted on the hood.Ford part # C9WY-16C630-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use after nearly 40 years.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.