Body

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Reproduction moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. This is a made in Taiwan part, and we recommend our used header mouldings. Ford part # C9ZZ-6503606-A.

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

Used driver side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A49.

Used driver side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A19-A. *NOTE* Often people think these come off with a pry bar when in fact they are to be removed from the inside of the car. For some reason when people remove them they always start with the drivers side thus the premium price... This icon means that we're looking to buy this...

Used passenger side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A48.

Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...

Factory spare tire hold down bolt for 1969-70 Mercury Cougar convertibles with style steel wheels. Note the felt and jack placement. Overall length 12-1/4 inches. As always, the threads are 1/2"-13.

Unique to 1970 convertible only. Only with stock steel wheels and hubcaps. J bolt MPC lists the length as 6-1/4 inches, with 4 inches on the end threaded but actually there are only 2 1/2" on the threads. Threads 1/2-13.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

This used driver (left hand) side lower front fender patch panel is rust free with no prior damage. Cut with a plasma cutter, removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 70 has the bigger, recessed side marker lights and the 69 has the smaller style. ...

This used passenger (right hand) side front lower fender patch panel is rust free with no prior damage. Cut with a plasma cutter and removed from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 70 has the bigger, recessed side marker light and the 69 has the smaller marker. ...

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Reproduction patch panel for the front of the driver side (left hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the front of the passenger side (right hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series. 

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

Currently we do not have any of these prop rods in stock, and we have yet to find a supplier to make it. If you or someone you know has the means to manufacture something like this, give us a call and let's talk. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" driver (left hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side rear quarter panel. We ask that you call to discuss condition, price, and cut...

Reproduction passenger side (right hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970. The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This reproduction measures approximately 29-1/2" at the wheel opening. ...

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Decor style rear interior panel for 1970 Mercury Cougar hardtops. Decor is one level above the base standard interior. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Standard style rear interior panel for 1970 Mercury Cougar hardtops. Standard interior was the base level interior design. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Armrests sold separately. Specify if your needs require power window cutouts in the comments section.

Standard style rear interior panel for 1970 Mercury Cougar hardtops. Standard interior was the base level interior design. Interior code for base standard interiors starts with 1, Decor interior codes can start with 3, 5, or E, followed by another letter denoting color. Arm rests sold separately.Specify if your needs require power window cutouts in the comments section.

Used XR7 rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in white for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in white for the passenger side (right hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Good used Grade "A" rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used,...

Good used Grade "B" valance. These valances may have some surface rust and a few dings or dents. You will definitely have to do work on these to get them ready for paint. We now sell a very high quality reproduction that is made of thicker material than OEM. Ford part # C9WY-6540544-A.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

This three part clip was used on all four versions of the 1969 - 1970 remote mirror to keep the door glass from interfering with the cable.