All Available Parts - 1968 Ford Mustang

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

The knobs for the seat track release to adjust the position of the seat. The reproduction has a slightly deeper divot where you place your finger, and is slightly more round on the bottom, but a very nice reproduction. Replaces Ford Part #: C5AZ-6261753-BA.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1969 small block, and will work for the 1967 or 1968 with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang /...

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Applications, 1968 289/302 engines without air conditioning, but with dual alternator belts. 390/427/428CJ engines without air conditioning. Casting number 6AA. 4-21/32" diameter and 7/16" sheave width. *NOTE* This is a good alternative for the hard to find AG pulley.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.

Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.

Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.

Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.

[No Description Provided]

Economy version of the clutch adjusting rod that fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Fits Standard and XR7 Sold as a Set as Pictured.

These reproduction door hinge bolts are for the Mercury Cougar and Ford Mustang and fit both standard and XR7 Cougar. They are sold in a set of 24.Intended for the 1968-70 hinges that are stamped steel, and not cast iron like 1967 hinges.

Sold as a Kit as Pictured.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, most customers will be happy with our reproduction ring that is not brushed. This...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator and 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most customers will be happy with our reproduction ring that is not brushed....

Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.

Exact reproduction of the 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work for 1969-70 Cougar and has the correct spring hook orientation. 66 - 68 Ford specs: 3-1/16" Long 40 Coils 69 - 70 Ford specs: 3-1/8" Long 36 Coils Replaces Ford part #: C3DZ-7523.

(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...

(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.

This attaches to the bracket mounted on the top side of your pedal hanger over to the clutch pedal itself. Replaces Ford Part #: C2AZ-7534-A.

Injection molded plastic stops underdash squeaking from clutch pedal return spring. 2 required per car. Replaces Ford Part #: C1DZ-7A630-A

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

Replaces Ford Part # : C7ZZ-7507-B

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.Sold Individually.We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Sold individually. Zinc (dark silver)

Self threading white plastic. Used on front and rear valances.Sold individually.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

Set of 6 bolts for installing an OEM Ford timing cover marked C8AE-6059-A, which originally came on all 1969-70 Mercury Cougars with 289 / 302/ 351W engines or 1968-70 Fords including Mustang with 289 / 302/ 351W engines. 4 short and 2 long bolt in this kit.*Note this kit is not applicable to the early designed Ford timing cover, see related items for other kit.

Set of 10 bolts for installing an OEM Ford timing cover marked C8AE-6059-B, which originally came on all 1968-70 Mercury Cougars with 390 / 428CJ / 427-4V engines or 1968-70 Fords including Mustang with 352 / 390 / 428CJ engines. *Note this kit is not applicable to the 1963-67 designed Ford FE timing cover, see related items for other kit.

Reproduction stainless Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.

Reproduction black Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Crankshaft oil slinger for all FE Ford V-8's, starting 1958 until at least through 1976. 1967-69 390 engines, 1968 427-4V engines, 1968-70 428, 428CJ, 428SCJ engines, 1958-66 352, and 1968-76 360 engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter 3-5/16 inches. Ford part number B8A-6310-A.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

1967 - 1969 Mustang, Cougar, Fairlane GT, and Ford vehicles with FE Series 390-427-428-428CJ engines. Chromed steel "Power By Ford" valve covers. Original equipment on all "S", "W" & "R" code big block Cougars. Super detail, domed chrome valve covers with embossed "Power By Ford" lettering. Also has internal baffles installed as original, price per pair. Click on images to enlarge. ...

D shaped, slightly lower profile than the D0OZ-6892 and designed for the thinner stamped steel valve covers, no Ford part number on part. Replaces Ford Part # C6AZ-6892

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Reproduction Ford blue painted valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

Reproduction chromed valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

Description: The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is...

Z bar return spring for all 1967-68 Mercury Cougar and Ford Mustang. This is the upper spring, proper color and spring tension from original. This is the economy version of the concours spring above. Made in China.

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.

Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675

Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

OEM Style Oil Pan Gasket.

This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.

Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.

Reproduction Small Block Chrome Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Includes drain plug.

Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)

Rear valance and 1967-70 windshield defroster attaching hardware. Sold individually. Zinc (dark silver)

Sold individually. Phosphate & Oil (gray-black)

# 56350-S

Fits 1967 Standard and XR7

These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.

Fits Standard and XR7

Fits Standard and XR7