All Available Parts - 1968 Ford Mustang

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

Reproduction Fastener Kit - Deck / Trunk Lid & Hinges for the 1968 Mercury Cougar / 1968 Ford Mustang 

Replaces Ford Part #: 379670-s

Reproduction Lower Headlight Bucket Loom Clip for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

Multiple uses.5/8" from bend to center hole.

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Reproduction intake manifold nut for the 289 or 302 on the 1968 Mercury Cougar and Ford Mustang (and possibly other Ford / Mercury cars). 5/16-18 X .72 X .33 zinc free-spin flanged nut. Sold individually. Replaces Ford part #: 374031-S

Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

Replaces Ford part # C2DZ-6A529 Sold Individually.

Reproduction water pump bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These are zinc (dark silver) plated and sold individually. This bolt is approximately 2-5/8" to the shoulder and an approximate overall length 2-3/4".

NOS water pump bolt for the Mercury Cougar or Ford Mustang. This bolt is approximately 3-1/2" to the shoulder and an overall approximate length of 3-3/4".Replaces part # 376258-S.

 Cylinder head bolt for any 1965-73 Ford 260, 289, or 302 engine 1965-73. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 260 / 289 / 302 engines. * Note - Does Not fit 351W cylinder heads!

This is the shorter version of the top-loader with no "+" on the head. Sold individually

Replaces Ford part # 385664-S

Bolt that attaches engine mount to block. 4 bolts per engine, used on all v8 engines Mercury Cougar and Ford Mustang 1967-68. Sold individually.Ford number 304668-S2

Sold individually Zinc (Dark Silver)

Sold individually Zinc (dark silver)

Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K

Sold individually, pivot stud for the aluminum power steering pump mounting bracket. fits all applications for small or big block.  Also used on the 1970 Mercury Cougar with 428CJ. Phosphate & Oil (gray-black)

Sold individually Zinc Dichromate (yellow-rainbow)

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).

Sold individually Zinc (dark silver)

Sold individually Zinc (dark silver)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292

Reproduction Radiator Mount Kit for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Reproduction dark zinc starter bolt for the Mercury Cougar or Ford Mustang equipped with the small block engine. These units are sold individually.

Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)

These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.

Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang

AMK engine fastener kit for 1968 Mercury Cougar / Comet, and Ford Mustang / Fairlane all with R code 428 Cobra Jet engines. This kit claims to have 145 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

Complete engine mounting hardware kit for the 1968 289/302 without A/C. See list below to see what comes in the kit. Click on image to enlarge.

AMK engine fastener kit for 1968 Mercury Cougar and 1968 Ford Mustang all with C, F, or J code 289 / 302 engines with air conditioning. This kit claims to have 137 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers,...

Sold individually. Zinc Dichromate (yellow-rainbow)

Reproduction Lower Radiator Core Support Loom Clip for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford Mustang 

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Complete under hood master fastener kit for the Mercury Cougar. While technically this master kit is for the 1968 Mercury Cougar, it will also work for the 1967 as well.

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

New valve cover bolts for all 289-2V, 289-4V, 302-2V, 302-4V, and 351W-2V, and 351W-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 12.*Note - Excludes Boss 302 and 351C engines (see part  number 8317)Replaces Ford part number 373071-S.

Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S

Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.

New set of bolts for fastening the transmission inspection cover on all 1967-70 Mercury Cougar, Ford Mustang, and Ford anything with 390, 428CJ, and 352 or any FE style Ford engine. Includes 3 and 4 speed transmissions.

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Reproduction valve cover bolts for all 390 / 427 / 428 Ford engines.

Reproduction bolts and washers for the C-4 automatic bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and code W automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1965-68.

Reproduction bolts and washers for the C-6 automatic bell housing on any 1967-70 Cougar or Mustang equipped with a 390 / 428 engines and code U automatic transmissions. Bell housing to engine block bolts. Fits most all other Ford big block V-8's from 1966-70.

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt set for any 1965-73 Ford 260, 289, or 302 engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford small block engines. Not for 351W cylinder heads. See related items for individual long or short cylinder head bolts.* Note, excludes 351W cylinder heads.

Cylinder head bolt set for any 1967-70 Ford 390 or 428CJ engine. 10 short and 10 long, Grade 8 cylinder head bolts. Proper lengths for Ford FE engines.  See related items for individual long or short cylinder head bolts.

Reproduction zinc front shock bolt with correct anchor symbol on the head, just like the originals.Sold individually.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Sold as a Pair. Ford Part #: C8AZ-2B296-A

Replaces Ford Part # 381985-S Sold individually

Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.

Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

New One-Piece, Rubber Coated Fiber Oil Pan Gasket for the 390, 427 or 428 FE Big Block engine in the 1968, 1969 or 1970 Mercury Cougar and Ford Mustang. 3/32" thick.

New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.

Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.

Reproduction oil pan bolt kit for the Mercury Cougar or Ford Mustang equipped with the 289, 302, or 351W engine.

New oil pan drain plug, Ford engine blue painted, with plastic gasket.  Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...

New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...

Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...

Oil pan bolt kit for all 428 Cobra Jet and 428 Super Cobra Jet engines with windage tray. Set is made by AMK and includes 20 OEM style bolts and washers. 

Used oil screen pick up tube assembly from a small block Ford 260, 289, or 302 engine. This is for most front sump 260, 289, or 302 engines in Ford cars up to at least 1972. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item.* Excludes 351W and 351C engines, and all F Series...

Small block dipstick tube for the 1968 Cougar and Mustang. Nice chrome finish to catch the eye. Will also fit on 1969 Mustangs with a 302 engine.

Small block dipstick tube for the 1968 Cougar and Mustang. Painted blue as original. Replaces Ford Part # : C8AZ-6754-A. Also fits 1969 Mustangs with the 302.

Nice chrome finish. Also available in Ford blue. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375 With the paint Stripped, it measures .365 It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A. ...

Also available in Chrome. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375With the paint Stripped, it measures .365It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A.

Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Engine oil dipstick as found on most any 1968 Ford with 289 or 302 engines (C, F or J Code). This has the correct bell shaped shield as found on 1968 and later cars. Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of shield to dip stick end is approximately 19.40 inches. The handles could have been painted black or blue originally.Ford casting # C8OE-6750-B.

Chromed engine oil dipstick as found on many 1967-69 Ford with 390 engines (S Code), 427-4V (W Code), 428CJ (Q or R Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end varys at either 19.25" and approximately 20.25" (full, add, and safe marks are the same). The handles were chromed originally. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Painted engine oil dipstick as found on many 1967-69 Ford with 390 engines (S or X Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. From the top of the shield to the dipstick end varys from either 19.25" to approximately 20.25" (full, add, and safe marks are the same). The handles were painted blue originally. Typically the painted dipsticks were found on the non-GT (6.5 Litre) cars in 1968. Ford part # C7AZ-6750-A, Ford casting...

Correct detail. Chrome plated with oval-style FoMoCo script stamped into the top surface of cap. This is a push on cap and requires the type of cap that has a round filler tube protruding from the driver side valve cover. This is the correct Open Emissions oil cap for the finned "G" valve covers we sell.

Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.

This cap is an exact reproduction of the original. Features include three filters and the AUTOLITE logo. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal concours reproduction. Fits the 67, 68, 69, and 70 Mercury Cougar. Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968 Ford cars sold in the US, had metal elbows. ...

This cap is an exact reproduction of the original. Features include three filters, the AUTOLITE logo and a beautiful chrome finish. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal ( concours reproduction). Fits the 67, 68, 69, and 70 Mercury Cougar. Available in Black or Chrome Finish.Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968...

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Used 1968 black Autolite oil fill cap with correct square metal elbow. Very limited supply of these. Reproduction, Ford service replacement, and oil caps installed starting in 1969 utilize a black plastic elbow. Reproduction steel elbow and rubber grommet available for those who already have an Autolite oil fill cap. Several variations noted from our collection, no doubt possible San Jose and Dearborn supplier differences.Replaces Ford part number C8AZ-6766-A.

Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.

Chromed "Autolite" oil filler cap, original cap chromed, not reproduction. Bare cap, will need baffle material added. Also recommend purchase of a rubber grommet and either plastic or steel PCV elbow. Your specific application will determine if plastic or steel elbow. See related items. C8AZ-6766-B$40 refundable core charge does apply.

Used 1969-70 black Autolite oil fill cap with black plastic elbow. Very limited supply of these. Reproduction, Ford service replacement, and oil caps installed starting in 1969 utilize a black plastic elbow. Several variations noted from our collection, no doubt possible San Jose and Dearborn supplier differences. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to...

Oil filler cap elbow for hose that goes to the air cleaner elbow. Black plastic like original, fits 1968-70 Mercury Cougar and Ford and Mustang. See related items for grommet and other related parts.

C7AZ-6582-A Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1969 Mercury Cougar with 390 engines. We are pretty sure that these painted valve covers were installed on non-GT cars without the engine dress up kits. Most 6.5 liter cars and the X code 390-2V would have had these painted valve covers. Right is the same as left, these are sold individually. Getting hard to keep in inventory, plan on some minor rust and or straightening. A good junk...

C7OZ-6582-C Chromed valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1970 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. These are used, and will have some minor pitting or stains in the plating.Sold individually *Restoration Tip - The difference between the chromed 390GT valve cover and painted valve covers is only the chrome plating. *Note - Some 1969-70 428 Cobra Jet engines came with one of two different styles of finned cast aluminum valve covers. ...

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Fits 1968 - 1970 Standard or XR7

Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.