Body

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

THE QUALITY ON THESE HOOD SCOOPS HAS DECLINED GREATLY, AS OF NOW WE WILL MOST LIKELY NOT BE ORDEREING ANY MORE UNTIL THE ISSUES ARE CORRECTED. Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This...

BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The Scoop measures 21 5/8" at the widest point on the front, 25" at the widest point at the rear and 26 1/8" tall when stood on end and measured at its longest point. The scoop is 2 7/8" tall at the front middle when mounted on the hood.Ford part # C9WY-16C630-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use after nearly 40 years.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Used moulding for 'upper windshield garnish' for any 1969 Mercury Cougar. This item not for convertibles. Item comes in black as shown, paint to match non-black interiors. Ford part # C9WY-6503606-A.

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

Used driver side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A49.

Used driver side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A19-A. *NOTE* Often people think these come off with a pry bar when in fact they are to be removed from the inside of the car. For some reason when people remove them they always start with the drivers side thus the premium price... This icon means that we're looking to buy this...

Used passenger side rear top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top. These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65424A48.

Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...

Factory spare tire hold down bolt for 1969-70 Mercury Cougar convertibles with style steel wheels. Note the felt and jack placement. Overall length 12-1/4 inches. As always, the threads are 1/2"-13.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Reproduction patch panel for the front of the driver side (left hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the front of the passenger side (right hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series. 

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Reproduction passenger side (right hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970. The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This reproduction measures approximately 29-1/2" at the wheel opening. ...

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

Used décor rear interior panel in aqua for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.