Body

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Here are our reproduction black 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

Here are our reproduction white 428 CJ fender decals for your Mercury Cougar. These are the same size and font of the originals and would look killer on any Ford equipped with the 428 engine. We were able to get our hands on a NOS decal to use for reference, so these are spot-on. See pictures for placement on the fender. Each decal measures 5 9/16" x 7/8".Replaces Ford part # C9WY-16228-B.

New rear seat to trunk steel divider for your Mercury Cougar. We had this one made specifically for the Mercury Cougar and it is designed to replace the flimsy tar based cardboard factory divider.We have noticed that after 40 plus years of chassis flex, the welds on the cross braces behind the rear seat tend to be broken. When installed properly behind the rear seat, this 18 gauge steel divider will provide stiffness to the chassis. This divider can be bonded, screwed or welded into your car...

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Reproduction of the 1969-70 Mercury Cougar XR7 door panel door grab handle or door pull ends and caps. Also found on 1969-70 full sized Mercury cars and 1968-70 Lincoln Continental MK III. Chromed end originally had a Mercury part number of C9MB-5422668-A, and the flat covers had a part number of C8MB-5422678-A. Nice reproduction of the covers, although we feel that they are a tad too shiney. Sold in a set of 8 pieces, enough for two door pulls.

This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222405-A.

New Old Stock part for 1969-70 Mercury Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!  Handle only, no button or hardware with this item. NOS does not necessarily mean perfect chrome. Look at the pictures, item pictured, is the item shipped.Ford part # C6OZ-6222404-A.

This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222404-A.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522601.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522600 on the right and C9ZZ-6522601 on the left.

Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part Number C9ZZ-6522600.

Made in America using original Ford tooling. No excuses, premium quality part. Right is the same as left.

This used button comes with the original spring and rubber grommet as shown. Our new door handle kits do not come with the spring shown here so if you need these small items to complete your handle assembly this is the listing for you! Also fits Torino, Ranchero.

This quality kit includes gaskets and buttons for both the passenger and driver side. The fit and finish is perfect on these, No excuses here, satisfaction guaranteed. These fit many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Fairlane, Australian Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG! Replaces Ford part numbers C6OZ-6222404-A and C6OZ-6222405-A ...

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks.You will want to purchase a new hinge pin and 2 bushings though. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C9ZZ-6522811-A. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C9ZZ-6522810-A. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase new pins and bushings though. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # D0ZZ-6522801-A. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase new pins and bushings though. ...

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Includes 4 cut to length hinge pins and 8 hinge bushings. Replaces Ford Part #: C9ZZ-6522800

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Many 70 - 73 cars used 3 pin type switches for the optional automatic seatback release feature. Sold individually. Additionally, this switch for the 3/4 inch mounting hole was used on 1968-70 Full sized Ford such as Custom, 500, Galaxie, LTD, and XL models, full sized Mercury such as Monterey, Montclair, Marquis, and Park...

Door latch actuating rod with adjuster for all 1969-70 Mercury Cougar and Ford Mustangs. Curved end hooks to the outside door release button lever. The threaded lower end with adjuster attaches to the latch mechanism. Main threaded rod has a Ford part number of C9ZZ-6522152-A. Adjuster has a Ford part number of C5AZ-6221816-A. Same rod fits either the passenger or driver side doors.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Steel stamped complete latch. See hardware for clips.

Used driver side (left hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected for excessive wear. This latch does have the ability to mount the door ajar switch, as found on all XR7 models. Door ajar switch sold separately. Must use the 1969-70 door ajar switch with this mechanism. Ford part # C9AZ-6221813-A. ...

Finally an affordable reproduction is available. Steel stamped complete door latch assembly that goes inside your passenger side door and catches on the door striker assembly. See hardware for clips. Replaces Ford Part # : C9AZ-6221812-A

Used passenger side (right hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected, this latch does the have the provision for the door ajar switch as found on all XR7 models. Door ajar switch sold separtely. This will fit all years 1967-70, was used as a service replacement. Just has a shorter tab for the key lock rod. Must use...

Steel door latch reinforcement repair kit. Countersunk bushings and screws for reinforcing the inside the door mounted latches on 1967-70 Mercury Cougar and Ford Mustangs. Kit has 6 machine screws and bushings, enough for both doors. The metal on the doors is very prone to cracking in the screw area for those latches.

Ford calls this Rod - Door Latch Push Button. This is the inside driver side manual door locking rod. Side specific to the driver side on any 1969-70 Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number C9ZZ-6521853-A.

Ford calls this Rod - Door Latch Push Button. This is the inside passenger side manual door locking rod. Side specific to the passenger side on any 1969-70 Mercury Cougar and Ford Mustang. The threaded end is where the chromed plastic manual lock button attaches. The lower end hooks onto the door latch. Ford part number C9ZZ-6521852-A.

Often when your door will not latch this is the culprit.

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1969-70 Mercury Cougar.* Note will not fit Mustang due to the door handle difference.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1969-70 Mercury Cougar.*Note will not fit Mustang due to the door handle difference.

Here is an example of what you can expect from a grade "A" pair of 1970 decor door panels from us. These are given the grade "A" rating because there is minimal discoloration and light general wear. These panels are very hard to find in grade "A" condition. Keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$600.NOTE: The...

Here is an example of what you can expect from a grade "B" pair of 1968 decor door panels from us. These are given the grade "B" rating because of the obvious wear and discoloration. These panels are very hard to find in grade "A" condition. Keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$550. NOTE: The pictures shown here...

Used grade "A" pair of XR7 door panels for the Mercury Cougar. Keep in mind you would not want to paint these panels if at all possible as they have streaks of black in them that cannot easily be duplicated. Black panels would be the exception. Also keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$600. Often at least one map...

Here is an example of what you can expect from a grade "B" pair of 1968 decor door panels from us. These are given the grade "B" rating because of the obvious wear and discoloration. These panels are very hard to find in grade "A" condition. Most of our panels range in price from $250-$550.NOTE: The pictures shown here are file photos from sets we have sold in the past and are not the actual panels or color you will receive. Please email or call for current colors and conditions of stock on...

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!