Body

Keyed alike as the originals were, includes two keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar.

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. C9WY-6543283-A.1969 and 1970 Cougar only.

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

1969-70 Mercury Cougar and Ford Mustang door lock rod. This is the short rod that goes between the door key lock and the latch mechanism. Same part right or left, just under 6 inches in length, no threads on this rod. Ford part number C9ZZ-6522134-A.

Includes three cylinder clips, two door cylinders, two door cylinder gaskets, two keys, one trunk cylinder, one trunk cylinder gasket, and one ignition cylinder. Made by the original OEM supplier. Makes 1 key fit all our locks! Replaces Ford part #: C9AZ-6222050-A

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has the elongated hex socket portion. There is also a version that has a rounded upper section formed on the socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A...

Not 100% concours correct but close close in design to the 1968 - 1973 handle. Works well for 1967 as well. Replaces Ford Part Numbers: C5ZZ-17032-A, C5ZZ-17032-B ,C8ZZ-17032-A, D0ZZ-17032-A, D4ZZ-17032-A.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts...

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has a rounded upper section of the hex lug socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A (Factory Service Replacement since 1974) If you'd like a particular...

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

Original, used hard plastic 1969-70 driver side mirror pad / gasket. Fits 69-70 driver side Sport mirrors, and 69-70 driver side Chrome mirrors on the Mercury Cougar. Will not work on the passenger side. Notice this is not a flat pad but has an angle built into it. MUCH better fit than the mushy flat rubber repro. Ford part # C9WY-17724-A, Ford engineering # imprinted on gasket C9WB-17C701-A Do you have riv-nut questions? Here are riv-nut answers! ...

Driver side (left hand) mirror pad / gasket made of very soft rubber. Fits 69-70 driver side Sport Mirrors, and 69-70 driver side chrome mirrors on the Mercury Cougar. Will not work on the passenger side. While this is "better than nothing" it will never fit or look correct. We highly recommend purchasing our good used hard plastic mirror pad that is especially contoured to fit the door on the driver side. Replaces Ford Part # C9WY-17724. Do you have riv-nut questions? Here are riv-nut...

Authentic looking hard reproduction plastic Sport Mirror pad gasket. Correct for driver side Cougar Sport Mirrors 1971-73 and passenger side Torino / Cougar Sport Mirrors 1970-73. This is the best fitting gasket we've found so far. You may have to punch out the hole for the remote mirror cable. Replaces Ford #: C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using...

Curved Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford Part # C9ZZ-16A052-BRB. ...

Curved Monte Carlo Bar in a chrome finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-BRC. ...

Straight Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-ARB.

Good used motor taken from 1967 through 1970 Cougars. Motor has been taken apart, cleaned, serviced and tested. These were used on the early Porsche, Mercedes, Maserati and Ferrari power windows and sunroof as well. Bosch part number 0 132 001 004. We only sell these on an exchange basis and you must send your core in advance. Keep in mind that you should remove the 4 rubber insulators before you send your core in, our units DO NOT have them installed. ...

Interior windshield / A pillar post mouldings / trim for 69 - 70 Cougars and Mustangs that feature two 2" gauge pods on the driver side. Sold as a pair.  These are not the best fit but will work, notice it requires exterior screws to mount them. No returns.

These are reproduction driver side (left hand) and passenger side (right hand) drip rail mouldings / trim for the Mercury Cougar equipped with a vinyl top. The vinyl top cars have a wider top edge but a narrow bottom edge. The non vinyl cars have a narrow top edge with a wide bottom edge. We will give credit for your original restorable cores. Replaces Ford part # driver side C9WY-6551726-D, passenger side C9WY-6551727-D.

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim for the Mercury Cougar equipped with a vinyl top have had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be...

This restored driver side (left hand) drip rail moulding / trim has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail mouldings / trim. The vinyl top cars...

Restored quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

Used quarter window to drip rail moulding / trim for the driver side (left hand) of the Mercury Cougar. This stainless trim part affixes to the "C" pillar and fills the gap between the roof side weather strip and drip rail gutter. Also known as "Roof Side Cover Retainer."

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

This obscure little part fills the gap on the underside of the roof rail where the rear 1/4 window meets the "C" pillar. Also known as "Roof Side Cover Retainer"

1969 - 1970 Cougars came factory equipped with stainless trunk mouldings and 1967 - 1968 Cougars came equipped with anodized aluminum trunk lid mouldings. However if you ordered a 67-68 service replacement deck moulding from Ford anytime after 1968 you would have received a stainless steel replacement. We recently obtained 15 of these that were stored improperly where the packaging had deteriorated and the mouldings showed shelf wear. We sent them out to be polished and the results are...

This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. Seven clips are...

This option REQUIRES sending your core in advance. This is a freshly restored 1969-70 original stainless steel deck lid moulding. It has had all minor dings and creases it may of had professionally removed and has been polished to a mirror like, better than N.O.S. finish. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the...

Used stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967-68 Cougar is that it will not match the aluminum corner mouldings perfectly. This being a used, means that it will have minor scratches, and a small dent or two. Save your old mounting clips, these are sold without...

This part will have a crack, usually at the top. Convertible and coupe used the same plastic trim. Add your desired color in the comments section.

Very hard to come by in perfect condition with no cracks. Both coupe and convertible use the same piece.

This plastic part will have a minor crack at the top. Add desired color into the comments section.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Used passenger side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top.These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A18-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

For all 1969 Mercury Cougar trunks. The MPC lists the correct length as 8-3/4 inches in total length, with 4 inches of the end being threaded but we have found without fail them to be about 10 3/4" with about 3" of threads. I say "about because some have a blunt end while other versions have a tappered end which will add about 1/8" to the length. Those threads are 1/2-13.

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. NOTE: Package Tray has a perforation you have to bend on...

Wow! Almost nothing is 100% correct about these rear package trays... No, your monitor is not out of adjustment, these colors are truly wrong except for the black. A couple of the colors are "close" to original but most will have to be repainted if you are concerned about correctness. The mesh is much lighter weight than the original and the speaker holes are not exact but the fit is good and overall this is a durable attractive piece. If you buy the insulation pad that lies beneath this panel...