Body

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 69-70 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

These weigh .50 pounds each, exactly as the originals do. Just like the originals, these are very prone to scratches and dents, even letting your seat belt fall will mark them up. Although these sill plates are better than our economy version, we still rate them below OEM which was also prone to damaging easily.  We HIGHLY recommend the stainless version we sell. These are sold individually, coupe, convertible, left and right are all the same. Decals are sold...

These are the same left to right, convertible or coupe. These appear to be made from the same thickness of aluminum as original and weigh .44 pounds as opposed to .50 for the originals but the aluminum used is not nearly the quality of originals. You can literally mutilate these parts with your fingers as you would an aluminum can. We recommend the premium quality sills. These are a poor reproduction that will not hold up well over time, we cannot recommend this part. We HIGHLY recommend...

Worn, scratched, dull but usable. Will have dents from seat belts.

Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* Since these are stainless they look great next to our "accessory" stainless steel sill plates we offer. The secondary "accessory" strips cover the painted portion of the door...

Sold individually, prior to purchase you will have to email us for colors on hand, as we do not have very many in top condition. The repro version of this grille is very good, so the only reason you would buy used is if you want a certain color (reproductions only come in black) or if you only needed one side.

Economy quality door speaker covers made from plastic injection. This version does not have a metal grille, the entire grille is made of plastic. In most situations we would recommend the Premium version as it has metal grilles; the all plastic version will cover the hole and will look correct if you don't inspect them closely, but is much easier to accidentally punch a hole in and will not stand up as well over time. The economy version also has a "Stereo" sticker instead of the correct...

Premium quality door speaker covers that have the OE correct durable metal grille mesh, unlike the economy version which is made entirely from plastic. The plastic version is much easier to accidentally punch a hole in and will not stand up as well over time. These grills also include the original style aluminum "stereo" decals, as compared to the economy version which has a simple sticker. Sold as a pair.All 1969-70 Mustang and Cougar door panels are equipped with a factory perforated "knock...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

Very nice reproduction, silver zinc finish like original. Correct texture and even an original type date stamped on the head. Comes complete with striker plate, shim, and screws. The only difference between the 67 Cougar and the 68 - 70 is that the 67 came with the 8-66 date stamp, the rest came with the 11-67 date stamp. Note: Some Cougars did not have date stamps from factory. Replaces Ford part # C5AZ-6222008-B.

Reproduction polished stainless steel door strikers for your Mercury Cougar or Ford Mustang. This kit includes stainless steel hardware and will make your door jambs pop.Replaces Ford part # C5AZ-6222008-A.

C9AZ-6521760-A Front door window stop bracket. Stops the window in the up position. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door.Same bracket is used on both driver and passenger sides.

C9WY-13A769-B-AGRADE Left side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

C9WY-13A769-B Left side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

C9WY-13A769-D Left side door wiring harness that includes door ajar, courtesy lights, and factory stereo door speaker harness. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package and Stereo option. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

C9WY-13A769-D Left side door wiring harness that includes door ajar, courtesy lights, and factory stereo door speaker harness. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package and Stereo option. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

C9WY-13A769-C-AGRADE Right side door wiring harness that includes door ajar, courtesy lights, and factory stereo door speaker harness. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package and Stereo option. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

Used custom cut driver side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551701-A

Used custom cut passenger side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551700-A

This restored driver side (left hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used...

This restored passenger side (right hand) drip rail moulding / trim for the Mercury Cougar equipped with a vinyl top has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good...

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Black stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same 3M satin black vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

White stripe kit for the 1969 Cougar Eliminator. This is the most correct kit you'll find anywhere. Designed using a NOS stripe kit as a reference, and cut from the same kind of 3M vinyl that Ford used from the factory. Kit includes 8 pieces for the fenders & extensions, doors, and quarter panels.Copy of original Ford decal instructions included. Note that these stripes are supposed to go on in a straight line, they do not curve down with the body line. See car picture in this listing for...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Sold as a Kit as Pictured.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

This kit mounts the wing to the pedestal.

Our grade "B" fenders are often what many would consider Grade "A". "B" Grade fenders may have damage around the wheel lip from over sized tires or very minor rust at the bottom corner or a fixable dent but they will not have all of these. We know what body work costs and we do not save junk. We also have many fenders that would be considered grade B+ or A-, give us a call for detailed descriptions of what we currently have on hand. Keep in mind that when ordering multiple over-sized items...

Reproduction driver side fender for the 69 - 70 Cougar. The main thing you'll want to notice is that there's no side marker light cutout, so you'll have to measure the placement of your existing marker to get it right. Without a cutout for the side marker, these fenders will work for both 69 and 70 Cougars. Also, the inner front panel is not attached to the fender, it will need to be welded into place. Keep in mind that this is an oversized package, so you can expect to pay $300 or more for...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well...

Our grade "B" fenders are often what many would consider Grade "A". "B" Grade fenders may have damage around the wheel lip from over sized tires or very minor rust at the bottom corner or a fixable dent but they will not have all of these. We know what body work costs and we do not save junk. We also have many fenders that would be considered grade B+ or A-, give us a call for detailed descriptions of what we currently have on hand.

Reproduction passenger side fender for the 69 - 70 Cougar. The main thing you'll want to notice is that there's no side marker light cutout, so you'll have to measure the placement of your existing marker to get it right. Without a cutout for the side marker, these fenders will work for both 69 and 70 Cougars.  Also, the inner front panel is not attached to the fender, it will need to be welded into place. Keep in mind that this is an oversized package, so you can expect to pay $300 or...

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1969-70 Mercury Cougar and Ford Mustang. Ford part number C9ZZ-16A006-A passenger side, C9ZZ-16A005-A driver side.

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-16A168-B, Mercury MPC # C9WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" fender extensions have a few dings, scrapes or warping due to over tightening of studs. Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.

New old stock 1969 Mercury Cougar Passenger Side Front Fender Extension Ford part # C9WB-16A168-B, Mercury MPC # C9WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Mercury Cougar front inner fender splash shield featuring all plastic construction. Ford part # C9WB-16A563-A, MPC number C9WY-16A574-A.