Interior

Dark Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Nugget Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Saddle windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

White windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark red rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction light blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Good used trim part that helps hold the rear panels in place. It is known as windlace or pinch weld moulding. There are two types of this trim found in the 1967-68, the rough or smooth textured version as shown. Please enter your desired color and texture into the comments section.

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction saddle rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction white rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Show-quality triple chrome plated passenger side quarter window frame for 1967-68 Cougars. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait until you receive your restored pieces to get reimbursed. Note: Badly pitted window frames may not be restorable, as the pits will need to be sanded out. If they are too deep, they may leave...

Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.

These are correct for XR7 or standard 1967 models. Used handles are almost always pitted due to lack of use. These are different than the front in that they are held on with an Allen set screw and are shorter in length. Replaces Ford Part #: C5ZZ-6530322-A. *NOTE* We have no good used examples of these rear window cranks as they are very prone to pitting over the years.

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

Used lower wiring harness for the overhead console on the 67 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs down the C pillar, under the door scuff plates and exits on the passenger side under the dash. That's where it connects to the under dash wiring harness. The upper harness runs from the overhead console, under the headliner and back to the C pillar where it connects to this lower harness. You can get the upper harness here. Ford Part Number C7WB-10C877-C ...

Used upper wiring harness for the overhead console on the 67 - 68 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs under the headliner from the overhead console back to the C pillar, where it connects to the lower harness. You can get the lower harness here. Ford Part Number C7WB-10C877-F

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1967 Mercury Cougar standard model 65A or 65C. The 1967 parking brake light kit gets its power from the ignition switch. Ford part number C7WB-10A841-A.

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Used blue plug pigtail that runs from the main 14401 harness to the taillights / emergency relay / C pillar lights.

Good used grade "A" core plastic passenger side bezel that may have had one or more very minor cracks repaired. One or more studs on the back may have been repaired as well. Finish will be poor or non existent but this bezel, unlike many we see will not have noticeable UV damage which makes them very brittle and prone to future damage.

Good used core plastic bezel that has had one or more cracks repaired. Multiple studs on the back side will show repair work. Finish will be poor or non existent.

Quality plexi-glass lens that is ready to install. Just peel off the protective tape and carefully pull your clock apart and replace and reassemble.The originals had a very slight concavity to them and these differ in that they are made from common, flat stock. These are also available already installed in our rebuilt clocks if you would prefer not to have to install the lens yourself.Check out the video below on our new gauge tester: ...

Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar

1967 Mercury Cougar XR7 Instrument Cluster Bezel / Housing Grade A - Used Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

[No Description Provided]

Reproduction 270 piece interior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Sun Visor Brackets Kick Panels Armrests (front) Seat Back Adjustment Scuff Plates Glove Box Catch Seat Back Scuff Plates Glove Box Latch Ashtray Liner Mirror Bracket (interior) Glove Box Liner Carpet to...

These are ready to ship now! Sold in a set of four. Specific to 1967 XR-7.There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch with a large shaft, 1968 with smaller shaft and 1968 with a small shaft that has been milled down on two sides. The reason Ford decreased the size of shaft in 1968 was to enlarge the thickness of the plastic on the toggle tips. By decreasing the size of...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A.These are manufactured in the USA. ...

Reproduction front armrest in saddle for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Used driver side (left hand) rear armrest for the Mercury Cougar that is in grade A condition. Grade "A" armrests are not pulling away from their backing and have no splits, cigarette burns or other obvious defects. They may need to be painted with vinyl paint, especially since we can almost guarantee we will not have both sides in your color in stock. Please indicate in the notes which color you would prefer, we will do our best to accommodate you. *NOTE* If you have a standard or decor 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight bend in the chromed quarter piece, whereas the early version is straight (see photo above). Made With Exact Materials As Original. Eight piece kit that includes inner and outer belt-line, enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them...