All Products

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Used under dash wiring harness repair bare ignition switch plug for the Mercury Cougar. This is the plug only, no wiring pigtail, and is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair bare ignition switch plug for the Mercury Cougar. This is the plug only, no wiring pigtail, and is part of the 14401 main under dash wiring harness.

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...

Exact replacement for that valuable AM-FM radio. This plug and pigtail is used to repair the radio out to speaker wiring so that it will plug into the plug for the speakers. Don't fake it and hack up your valuable under-dash wiring harness to make your original radio work! Fix it correctly the first time with this quality replacement piece.

Original used AM radio power under dash wiring pigtail for all 1968 Mercury Cougar (standard and XR7) and Ford Mustangs with factory AM radios. This double female plugged wiring pigtail is for your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. *Note - this wire is part of the main under dash or 14401 wiring harness.Fits: 1968 Mercury Cougar 1968 Ford Mustang ...

Used plastic shield affixed to the quarter to protect the wiring to the power window switch. Left and right are the same.Ford Part Number D1ZB-14A099-BB

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Reproduction Wittek tower hose clamp kit for the Mercury Cougar or Ford Mustang equipped with the 302 or 351 engine. This set of 10 clamps is concours correct and features the correct date stamps. It is often little details like this that separates first and second place when your precious Cat or Pony is being judged.

Reproduction Wittek tower hose clamp kit for the Mercury Cougar or Ford Mustang equipped with the 302 or 351 engine. This set of 10 clamps is concours correct and features the correct date stamps. It is often little details like this that separates first and second place when your precious Cat or Pony is being judged.

Reproduction Wittek tower hose clamp kit for the Mercury Cougar or Ford Mustang equipped with the 302 or 351 engine. This set of 10 clamps is concours correct and features the correct date stamps. It is often little details like this that separates first and second place when your precious Cat or Pony is being judged.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Reproduction Wittek tower hose clamp kit for the Mercury Cougar or Ford Mustang equipped with the 429 engine. This set of 10 clamps is concours correct and features the correct date stamps. It is often little details like this that separates first and second place when your precious Cat or Pony is being judged.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Listing is very good quality wood grain insert only. Plastic will be broken. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light.

Listing is very good quality wood grain insert only. Plastic will be broken. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

Good used grade "A" core plastic passenger side bezel that may have had one or more very minor cracks repaired. One or more studs on the back may have been repaired as well. Finish will be poor or non existent but this bezel, unlike many we see will not have noticeable UV damage which makes them very brittle and prone to future damage.Check out our dash bezel repair video: ...

Good used core plastic bezel that has had one or more cracks repaired. Multiple studs on the back side will show repair work. Finish will be poor or non existent.Check out our dash bezel repair video: ...

Quality plexi-glass lens that is ready to install. Just peel off the protective tape and carefully pull your clock apart and replace and reassemble.The originals had a very slight concavity to them and these differ in that they are made from common, flat stock. These are also available already installed in our rebuilt clocks if you would prefer not to have to install the lens yourself.Check out the video below on our new gauge tester: ...

Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar

New black oval Phillips headed screws with correct sized heads for seating into the original and reproduction 1967 XR7 rocker hash marks.

Fits 1968 Standard or XR7

1967 Mercury Cougar XR7 Instrument Cluster Bezel / Housing Grade A - Used Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10841

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent. Check out our video on dash removal and restoration:

Good used core plastic bezel that has had one or more cracks or breaks. Finish will be poor or non existent. Ford part number: C8WF-10841

[No Description Provided]

Reproduction 270 piece interior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Sun Visor Brackets Kick Panels Armrests (front) Seat Back Adjustment Scuff Plates Glove Box Catch Seat Back Scuff Plates Glove Box Latch Ashtray Liner Mirror Bracket (interior) Glove Box Liner Carpet to...

Fits 1968 Standard or XR7

Individual hash mark for anyone looking to replace a broken or missing hash mark. These are correct only for the 1967 XR-7 but will fit nice on any 1967 - 1970 Cougar and are a nice alternative to the very large aluminum rocker mouldings used in 1968 - 1970 on most models. These are MUCH better quality that what Ford originally put on the Cougar, you will not see any tiny imperfections or casting marks in the chrome plating and no over-spray in the black painted area. These are very...

New product! These 1967 XR-7 "hash marks" or "ribs" are being offered as set of 14. Seven of these were used on each side. These are correct only for the 1967 XR-7 but will fit nice on any 1967 - 1970 Cougar and are a nice alternative to the very large aluminum rocker mouldings used in 1968 - 1970 on most models. These are MUCH better quality that what Ford originally put on the Cougar, you will not see any tiny imperfections or casting marks in the chrome plating and no over-spray in the...

New old stock toggle tips or 'handles' as Ford called them. Fits 1968 Mercury Cougar XR7 models.   Ford part number C8WY-13B760-A. Do not put excessive force on the shaft as you may damage the switch internally.  These absolutely will not fit the smaller shafted 1967 XR7 switches. Click to Enlarge //--> There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch...

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

These are ready to ship now! Sold in a set of four. Specific to 1967 XR-7.There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch with a large shaft, 1968 with smaller shaft and 1968 with a small shaft that has been milled down on two sides. The reason Ford decreased the size of shaft in 1968 was to enlarge the thickness of the plastic on the toggle tips. By decreasing the size of...

The 1968 toggle tips we sell fit very tight at best.  To make them fit you will have to remove every bit of glue residue left from the old tips and you may even have to enlarge the holes in the plastic by boring them out a little with a drill bit.  Do not put excessive force on the shaft as you may damage the switch internally.  We apologize for the fit but once on you will have an attractive durable set of tips in place.  No returns on these although if you happen to...