All Products

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will work on all 1967-70 as well. But...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

Good used OEM original driver side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It is easier to fit and adjust these hinges prior to installing the springs on them. Here is a helpful youtube video that shows you how to...

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will also work on 1967-70 as well....

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. You can find the hood hinge apron nuts here. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with...

Good used OEM original passenger side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It will be easier to fit and adjust the hinge prior to installing the spring on the hinge. Here is a helpful youtube video that shows you how...

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This early 1969 version has the shortest handle, and is the hardest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-A.

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

Good used, rust free latch that is in good working order. This unit has not been straightened or pushed out after being in a fender bender. We also have many grade "B" latches in less than perfect condition. We also have the individual components listed. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Used, hood latch assembly that is in good working order. This unit will have a bit of metal shifting on the brace portion. Can be straightened fairly easily We also have many grade "A" latches. We also have the individual components listed. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

For use with hood dowel or latch part number C5ZZ-16929-A. Application 1967-68 Mercury Cougar, 1965-66 Ford Mustang, 1965 Falcon and Comet. Original Ford part numbers 33845-S8 & 351810-S8.

These reproduction hood latch support bolts fit both the Standard and XR7.

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

Used hood release latch by itself, this is a component of the hood latch assembly for any 1967-68 Mercury Cougar.

Correct stud configuration, size, and weight. This scoop was made by using an original 1972 Cougar GT scoop to make the mold. 1971-73 Cougar GT's, and the J code 429CJ with ram air, all used the same scoop. The dimensions are just like the original and measure 19-1/4" at the widest point on the front, 24-1/8" at the widest point at the rear, and 25-1/2" tall when stood on end and measured at its longest point. The scoop is 2-1/8" tall at the front middle when mounted on the hood. Paint job not...

Reproduction Non-Functional hood scoop that was originally used on the 427 GT-E, but will work on any 1967-68 Mercury Cougar and look great! This scoop measures 25 3/8" at its widest point, 26-1/2" at its longest point, and is 2" high. Originally, the recessed scoops in the front were painted black to give the illusion of an open scoop. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G...

Non functional scoop originally used on the 1968 Mercury Cougar XR7-G but will work on any 67 - 68 Mercury Cougar. This scoop measures 25 3/8" at its widest point, 26 1/2" at its longest point and is 2" high. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G and GT-E's most measure about 1 1/2" from the rear edge of the hood to the rear edge of the scoop at centerline. This differs from...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

This is the large horizontal bracket that reinforces the front bumper on any 1971-72 Mercury Cougar. This is one of 6 brackets needed for mounting the front bumper. These were bare steel and some of our used brackets will have some erosion or minor rust. Structurally they are fine. Replaces Ford part number D1WY-17A792-A.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. We do offer the correct used Cougar horns.Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B...

Tested and working used Hi tone horn. The High tone is indicated in raised letters located on the perimeter of the horn. 1967-68 Cougars used part number C7WF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.NOTE* - High tone horn is on the passenger side ...

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1971-73 Mercury Cougar used part number D0DF-13801-A Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used...

Tested and working used Low tone horn. The 'Lo' tone is indicated in raised letters located on the perimeter of the horn. 1967-68 Cougars used part number C7WF-13802-B Low tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.NOTE* - Low tone horn is on the driver side ...

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1971-73 Mercury Cougar used part number C8DF-13802-A Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

Good used grade A horn bar with nice, almost perfect chrome. Will have all three vinyl pads / inserts in place but we cannot guarantee we will have your desired color.Replaces Ford part number C7WA-3D755-A. Check out the very first Cougar in our video below!

Good used grade B horn bar with minimal pitting similar to what is shown in our pictures. Good for a driver quality classic or send it in for re-chrome for your show car. Will have all three vinyl pads / inserts in place but we cannot guarantee we will have your desired color. Please mention in the comments section what color you desire. Ford part number C7WA-3D755-A. Check out the very first Cougar in our video below! ...

This restored part will require that you glue your colored vinyl strips in place. If you send in a core, only cores with light pitting can be used to create a show quality finish product.Casting number as seen on back: C7WA-3D755-A. Check out the very first Cougar in our video below! ...

Set of three plastic spacers to replace your original brittle cracked parts. These are much stronger than OEM.

This listing is for one spring, plastic spacer and screw. Three of these are needed to mount your chrome three spoke horn bezel to your 1967 steering wheel. We also list reproduction 3D printed spacers. Check out the very first Cougar in our video below! ...

Very nice reproduction of the steering wheel hub decal with the walking cat to fit the new Shelby steering wheels. Chrome outer rim with plastic black and silver horn button in the center.

Used grade "A" horn center / pad in aqua for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately. Normal 0 false...

Used grade "A" horn center / pad in black for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock, so we'll do what we can to get a good pad for you. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately.*NOTE* Because...

Used grade "A" dark blue horn canter / pad for the Mercury Cougar XR7. This will fit and 1967 Cougar, but the dark blue interior color option was XR7 only. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The...

Used grade "A" horn center / pad in dark ivy gold / dark green for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the ivy gold interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can...

Used grade "A" horn center / pad in dark red / maroon for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the dark red / maroon interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can...

Good used grade B pad with dull trim ring and bad center emblem. Emblem will show discoloration, warping, cracks in the lens and maybe all three! Check out the very first Cougar in our video below!

Used grade "A" horn center / pad in light ivy gold / light green for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased...

Used grade "A" horn center / pad in parchment / off-white for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately....

Used grade "A" horn center / pad in red for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock so obtaining the color you desire would be a rare treat, but we will try our best to accommodate you. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring...