1971 Ford Mustang

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Four piece CLEAR window glass set for the 1971

Reproduction clear four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete five piece window glass set for the 1971

Reproduction CLEAR five piece glass set for the 1971-73 Mercury Cougar coupe or Ford Mustang hard top equipped with power or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete six piece window glass set for the 1971

Complete five piece window glass set for the 1971

Complete reproduction SMOKED glass set for manual crank or power windows. Included are the door glass

Reproduction six piece extra dark tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with manually operated windows. This set does not include any window trim so save your for reuse. There are three versions of this glass. The clear version is just that

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete five piece window glass set for the 1971

Reproduction six piece SUN-X or tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete five piece window glass set for the 1971

Reproduction TINTED five piece glass set for the Mercury Cougar coupe equipped with either power windows or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

1969-1973 20 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for accessory feed, seat belt warning, tilt swing column, speed control, door ajar, low fuel, and power window relay.

Used glove box catch for any 1969-73 Mercury Cougar or Ford Mustang. Ford part number C9AZ-6206064-A.

Sold individually, two required per car. Replaces Ford Part #: 375838

Reproduction Glovebox Liner w/ Air for the 1971 - 1973 Mercury Cougar and Ford Mustang

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Reproduction rubber grommet for the air conditioning case. This grommet encloses the tubes for the evaporator, and slides into a slot on the heater box. Owners with 1969 A/C please look at your existing grommet for the triangle shape like in the picture. Fits some 1969 Mercury Cougar and Ford Mustang (late built cars), and should be all 1970-73 Mercury Cougar and Ford Mustang. Replaces Ford part number C9ZZ-19B552-A. Check out our video below on how to replace a heater core! We used a '69...

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from a spongy rubber, attaches to the heater core and seals the firewall from the inside. This grommet does not use a retaining bracket like previous years. Will be intact, but will show some degradation as shown in the picture, most evident where the heater core tubes pass through. Engineering # D1ZZ-19B588-A.

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Reproduction two hole fuel line grommet for the Mercury Cougar or Ford Mustang.

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

Good used detail item that is often missing and is also correct for Mustang. Copper grounding strap. We have noticed that 1971 cars typically have a hex head screw, and the 1972-73 straps were attached with a hex head screw.

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 429CJ engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery.

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

D0AE-6316-A All 1970-73 351C-2V and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. There is a $50 core charge for this part.*Note - Excludes 1971 and later 351-4V engines. **Note - When ordering double check that you have a 351 Cleveland engine. It is not...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all 1971 M code and 1972 - 1973 Q code 351-4V or 351 Cobra Jet Mercury Cougar engines. Outside diameter is approximately 6-1/2 inches, and 1-1/2 inches thick. 1971-73 351-4V Cleveland have specific balancers, and are different than 1970 351C 4 barrel engines, please identify your engine and verify your balancer numbers. Has the timing marks on rim. Core charge is refundable when rebuildable D1ZE-6316-AA or D1ZE-6316-AB harmonic balancer is received by WCCC. Ford part #...

Includes all 1971 M code and 1972-73 Q code 351-4V or 351 Cobra Jet Mercury Cougar engines. Outside diameter is approximately 6-1/2 inches, and 1-1/2 inches thick. 1971-73 351-4V Cleveland have specific balancers, and are different than 1970 351C 4 barrel engines, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim.  Core charge is refundable when rebuildable D0OE-6316-B harmonic balancer is received by WCCC.Click on images to enlarge. This is a picture of a 40 year old piece of rubber...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford Casting Number: D1ZB-76514A72-AA