1971 Ford Mustang

Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Harmonic balancer or damper, core grade 1971 Boss 351 Ford Mustang. Marked D1ZX-6316-AA. Age cracks in the rubber, should be rebuilt prior to use. Groove opposite of timing marks as shown, no other visible issues. 

High quality, durable canvas cap with velcro closure. The hat now features our Web address on the back! "The baseball cap arrived Saturday but since I wasn't home, they didn't leave it for me. I picked it up today at the post office. It's real nice! Seems to be a higher quality cap compared to others I've worn. Thanks for sending it." Larry Check out this video of our 2013 Open House event! ...

NOS Ford replacement driver side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-B

NOS Ford replacement passenger side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-A

These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.

These steel tubes made to exact O.E.M. standards and specifications.

D1AZ-9A603-A Metal shroud for all 1971 351 engines including H code 351-2V and M code 351-4V. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel.

D1AZ-9A603-C Metal shroud for all 1971 429 Cobra Jet engines including C code 429CJ non-ram air and J code 429 CJ with ram air. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

New old stock hood bumper for any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, limited to stock on hand. Replaces Ford part #D1ZZ-16758-A

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

C9AZ-6A664-A Original used hose that connects the valve cover oil cap mounted PCV valve and the front of the Quadrajet carburetor base plate on 1970 through 1971 Mercury and Ford 429 Cobra Jet engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work)....

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Good used power steering pressure line hose retainer. Mounts on top of the shock tower brace as shown. Comes as shown with used rubber insulator. Fits all 1971-73 Mercury Cougar and Ford Mustangs with V-8 engines. Ford part # D1ZZ-3C510-A.

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Fits all 1971-73 Mercury Cougar and Ford Mustang with factory power or manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts.  Original Ford part number D1ZA-3355-A. Anghel Restorations...

Idler Arm Assembly for 1971-1973 Cougar and Mustang. Fits all 1971-1973 Cougars and Mustangs with manual or power steering. Complete with bushings installed and ready to bolt on. Does not include Zerk fitting. This Idler arm helps stop that floating feeling going down the road. Please see the installation photos below. Easy to install. 

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

Used bracket and pulley assembly with new installed bearing for Mercury and Ford equipped with the 429CJ, 429, and 460 engine. This assembly was also equipped on the 1970 - 1971 Torino, Ranchero, and Cyclone with the 429CJ engine. Also many other 429 / 460 engines. Listed in the Ford Master Parts Catalog (MPC) as D0AZ-8678-B. *Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Ignition housing / cover for the fixed steering column on 71 - 73 Cougars and Mustangs. Technically called a "Flange", the ignition cylinder sits inside this cover.This item will need to be re-painted to match your column.Ford Part number D0AA-3511-CW

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

D0ZZ-5493-A Rear sway bar bushing with 1/2" diameter opening. Used on rear anti-sway bar on the 1970 Eliminator and 70 - 73 models ordered with the competition handling package. Casting number as seen on the bushing is D0ZA-5484-E. Sold individually.

Cast iron intake manifold used on all 1972 Q code 351-4V or 351CJ engines in a Mercury Cougar or 1971-72 Ford Mustang. Stock 4 barrel spread bore intake manifold. Take off manifold with correct casting number of D1ZE-9425-BB . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1ZE-9425-BB. *Note - 351 Cleveland engines only.

D0OE-9425-D Cast iron intake manifold used on all 1971 C or J code 429CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0OE-9425-D. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. This unique manifold used a General Motors Rochester Quadrajet carburetor with a spread-bore pattern. Typical after-market carburetors like Holley will not work on this intake...

D0OE-9425-C Cast iron intake manifold used on 1970 and 1971 C or J code 429 Super Cobra Jet engines in a Mercury Cyclone or Ford Mustang or Torino. Stock square bore 4 barrel intake manifold. Square bore is four equal venturi holes normally for Holley carburetor applications. Take off manifold with correct casting number of D0OE-9425-C. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Not sure of the casting date.This cast...

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Reproduction jack and tool bag for the trunk area of your Cougar or Mustang. Made in the same plaid style as the trunk mat on the outside, and a white soft liner on the inside. Measures 16 1/2" x 8 1/2"

This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your mouse, you can have it at your door in a few days (more or less, depending on your location). Good for all sorts of projects around the house or garage.

NOS Key reminder buzzer for 1970-71 Mercury Cougar and Ford Mustang. Also used on 1970-72 Lincoln MKIII and Thunderbird. Can also be stamped DOAB-13150-B, DOAB-13150-E, and DOAB-13150-F. Ford master part number D0AZ-13150-E. NOTE: This buzzer is for ignition key reminder with two posts. The four post ignition / headlight buzzer can be found here. Click on images to enlarge. ...

One year only rod used on the 429 CJ with C6. Approximately 21" with pink color code.

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

Early 1971 wiper switch knob. Master Parts Catalog says before 5-3-1971. Thereafter through 1973, the part number is D1OZ-17513-A.

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for 97 and 631 bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these. ...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...