1971 Ford Mustang

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-3/8" oval holes. Sold individually, Usually 1 per car. Fits 1971-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 384440.

   Sold individually.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.

Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Sold individually Zinc (dark silver)

Replaces Ford Part # 43260-S Sold individually

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass.Click on images to enlarge. 1970 similar. ...

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Sold indiviually Phosphate & Oil (gay-black)

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Sold individually # 56354-S

Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.

Replaces Ford part # 385664-S

Replaces Ford part #375381-S Phosphate & Oil Finish

part # 56131-S

Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually 

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.

replaces Ford part # B-12764

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Replaces Ford Part # 382626-S Sold individually

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

This is longer of the two with the + on the bolt head.

This is the shorter version of the top-loader with no "+" on the head. Sold individually

part# 372821-S