1971 Mercury Cougar

Here's a new book about the king of classic Cougars, the GT-E! This book starts out with the standard '68 Cougar and XR-7 as both models were available with the GT-E option. The reader is then taken through the early stages with the XR-7S and prototypes. Following these pages is the GT-E as we all know it, and then a brief venture into 1969. Lastly are parts lists for the 427 GT-E and the 428 GT-E. This book was written for the casual reader as well as the GT-E enthusiast.The book contains...

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat.  Replaces Ford part number D0AE-8575-B.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Thermostat water neck or 'Connection - Water Outlet' as it is called in the Ford manuals. Fits 1970-73 351C or 351 Cleveland engines as found in 1970-73 Mercury Cougars and most all other Fords with the 351C engine. Cast aluminum housing.*Note - original water necks were cast iron, this is cast aluminum.Gasket not included. Find it here.

New thread sealant specially formulated to seal liquid in high temperature applications.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Inner tie rod end for 1971 - 1973 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D1ZZ-3A131-A

Outer tie rod end for 1970 – 1973 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Includes 1969 Boss 302 Eliminator and Mustang, and 1970-74 Ford Maverick and Mercury Comet. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: D0OZ-3A130-B.

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1970-73 Mercury Cougar, Ford Mustang, and many other Ford cars.Replaces Ford part # D0OZ-3332

Used timing chain cover for any 351C or Cleveland engine from 1970-74. Mercury Cougar and Ford Mustang and additionally fits 351M / 400M engines. All steel construction without excessive rust or damage. Installation bolt kits also avialable.Replaces Ford part number D0AZ-6B070-A.*Note - will not fit 351W or Windsor engines.

Set of 3 bolts for installing an OEM Ford timing cover, which originally came on all 1970-73 Mercury Cougars with 351C or Cleveland engines or 1970-74 Fords including Mustang with 351 Cleveland engines. Also fits 351M and 400M Ford engines*Note - this kit is not applicable to the 351W or Windsor engine. See related items for other kit.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

Tire Pressure / Tire Size / Maximum Load Decal for the 351, 351 GT and 429 1971 or 1972 Mercury Cougar

Used replacement toggle switch for the 71-73 Cougar XR7. This is a double throw switch that can be used in either the accessory, convertible top or defog positions on the switch assembly.

Used replacement toggle switch for the 71-73 Cougar XR7. This is a single throw switch that can be used in either the map or courtesy light positions on the switch assembly.

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

Sold individually Zinc (dark silver)

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

Manufacturer calls this a torque pin kit, it consists of 3 pins. Pin diameter is 1/2 inch and are 13/32 inches long. Made from natural nylon. Fits most Ford vehicles with power windows from 1964 - 1973+.

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1971-73 Mercury Cougar torsion springs D1WY-6544890-A and D1WY-44891-A. The body section of the shop manuals describe how to adjust these bars, we offer a torsion...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with H code 351-2V engine. Tag number PGA-AV. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with M code 351-4V engine. Tag number PGA-AH. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core FMX transmission for a 1971 Mercury Cougar or Ford Mustang. Tag number PHB-E2 or  PHB-E3. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Outer casing for the C6 transmission on the 71 - 73 Cougar or Mustang. Case only, does not include any of the inner workings or output shaft.