1970 Mercury Cougar

Reproduction Accessory wire with Buss bar for the accessory terminal found optionally on 1969-73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded style triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire length is just over 9 inches in length.

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

Individual reproduction anti-rattle rubber gasket for the stainless steel accent ring used on the Mercury Cougar or Cyclone. This unit is used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Sold individually.

Set of 20 reproduction anti-rattle rubber gaskets for the stainless steel accent rings used on the styled steel wheels found on the Mercury Cougar or Cyclone. These units are used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Set of 20

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

Reproduction antenna base gasket.Replaces Ford part #  C9WA-18298-B.

Here's a good original used antenna base gasket that is unique to the 1969-70 Mercury Cougar. Replaces part # C9WA-18298-B.

New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.

[No Description Provided]

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

OEM Style Oil Pan Gasket. Four Piece Gasket.

One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Replaces Ford part #C7AZ-13568

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.

Adhesive-Backed Gasket Material Helps Prevent Breaking of Water Outlet. Gasket Cement is Not Needed. Self-Adhesive Backing Holds Thermostat in Place While Water Outlet is Being Installed.

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

These 1969-70 Mercury Cougar chrome door handle gaskets are the closest fit to the original Ford gaskets on the market. 4 pieces as shown, enough for both door handles only, round lock gaskets sold separately.Will also work on 70-71 Cyclone and Torino.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

New timing cover gasket set for 1970-73 Mercury Cougar and Ford Mustang with 351C engine. Includes gaskets as shown, timing cover, water pump to timing cover, fuel pump, crankshaft seal, and oil pan saddle.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

New timing cover gasket set for 1970-73 Mercury Cougar and Ford Mustang with 351C engine. Includes gaskets as shown, timing cover, water pump to timing cover, fuel pump, crankshaft seal, and oil pan saddle.

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Gasket that creates the seal between the backup light lenses (also known as the reverse light lens) and the chrome housings on the 1969 and 1970 Mercury Cougar. Sold as a pair. Replaces Ford part # C9WY-15510.

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

Seals the lenses to the light body mounted in the front valance. Replaces Ford part # C9WY-13211. Sold as a pair. Also used on 1970 Mach I and 1969 - 1970 Shelby.

Seals the chrome marker light bezel to body. Seals the chrome marker light bezel to body. Their function is to keep water from entering the trunk around the rear lights. No gasket is needed on the front side markers. Replaces Ford part #D0ZZ-15447. These are designed for the Mustang and do not fit the Cougar without trimming. Sold as a pair.

These white foam gaskets fit between the sealed lens assembly and the chrome side marker light housing. They are sold as a pair. Replaces Ford part number D0ZZ-15209. *NOTE* To separate the sealed plastic lens assembly from the chrome bezels you will have to gently break away the edges of the factory "melted over" plastic stud. A drop or two of your favorite adhesive will reattach them but this is not crucial as the two threaded studs keep everything tied together once they are mounted back to...

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

These reproduction lens gaskets are a perfect fit and are sold as a pair for your Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...