1970 Mercury Cougar

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1969-70 anchor wires are 3-1/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire.

Contrary to what you might think at first glance, the support rods used in 1969 - 1970 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. 5 Rods total. Once installed in the car, each rod should be about the same distance from the roof as the other rods. WCCC marks the bows with a sharpie pen, 1 hash mark, 2 hash...

Reproduction frame used to stretch your headliner over on the interior side of your sliding sunroof panel. Since we do not have near enough of these to go around we also offer a cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable reproduction. 

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

This is the heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 2 Barrel Carburetor and the 351 Cleveland engine. Exact OEM standards and specifications. Correct fiberglass insulation, fittings and S clip.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up.  Made out of OE Steel.  This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

Exact OEM standards and specifications.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

Factory installed, used engine mount heat shield, for any 1969-70 Boss 302 Mercury Cougar Eliminator or Ford Mustang. Mounts to the driver side mount and the asbestos portion lays under the exhaust manifold. Basic Ford part number is 6C038 for motor mount heat shields.  *Note - this item will likely not work with headers.*Note - this part does contain asbestos.

Grade B exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade B used will have minor pitting, and may have small holes and or rough rusted edges. When mounted it would be difficult to see the defects. We also stock A grade versions.Replaces Ford part number D0OZ-9A603-F.

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

D0AZ-9A603-C This is a two piece metal shroud unique to early production 1970 H code 351-2V Windsor Cougars. Due to problems Ford had with this design they returned to the 1969 style later in the year (after 2-2-70). *Note - 1970 351-2V Windsor cars build before 2-2-1970 used a two piece heat shield. Also used air cleaner snorkel D0OZ-9A626-B and a paper 'S' tube. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970. After 2/1/1970, the stripe on the hose was changed to yellow. This hose features durable red striping with "Autolite" spelled out and is dated H9H04B. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have 90 degree elbows molded at one end which fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970. A red stripe was used before 2/1/1970. Durable yellow striping with "Autolite" spelled out and dated H0A13A. Correct for all V-8 engines WITHOUT air conditioning. Hoses for cars with A/C have a 90 degree elbow molded into one end that goes on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970 WITH factory or integral air conditioning. After 2/1/1970, the red stripe and date code was changed to yellow. Durable red striping with "Autolite" spelled out and dated H0A12A. Correct for all V-8 engines with A/C. Theses hoses have a correctly molded 90 degree elbow on one end that attaches on the water valve side. Some length trimming may be required for a tight looking fit. Turn those...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970 WITH factory or integral air conditioning. Before 2/1/1970 a red stripe was used. Durable yellow striping with Autolite spelled out and dated HOA13A. Correct for all V-8 engines with A/C. These hoses have the correctly molded 90 degree elbow that goes on the water valve side. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Dual heater hose tube assembly for the 1970 Mercury Cougar and Ford Mustang with the 428 Cobra Jet or 428 Super Cobra Jet engine. This heater hose attaches along the top of the passenger side valve cover. Length of long end: 13 3/8" Length of short end: 8 5/8" Replaces Ford Part #: D0ZZ-18B402-A.

This correctly formed heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Length: 13 9/16"Replaces part # D0ZZ-18696-A.

Used heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. Darn near impossible part to find in used form as they are always rusted out and nasty. One year only part.Ford part # D0ZZ-18696-A.

This correctly formed heater tube for the G code 1970 Boss 302 engines, attaches to the intake manifold on the passenger side of the carburetor. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Replaces part # D0ZZ-18696

New bolt for attaching the window guide to the door window bracket on any 1969-70 Mercury Cougar or Ford Mustang with glued in side glass. Two per guide (4 guides per car). 8 total, four on the passenger side, four on the driver side. 1/4"-20 x 5/8" Large Flange Spin Lock Bolt.

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.

This H5006 bulb is the closest Halogen Reproduction of the original FoMoCo headlights that we carry. This bulb has the number 2 at twelve o'clock (to indicate its position in your grille) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high / lo beam is definitely going to be brighter than your original dim bulbs. Also note: Other than Cougars, only the 1969 Mustang used these bulbs.Don't forget...

This H5001 bulb is the closest Halogen Reproduction of the original FoMoCo headlight that we carry. This bulb has the number 1 at twelve o'clock (to indicate its position in the grill) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high beam is definitely going to be brighter than your original dim bulbs. Note: Other than Cougars, only 1969 Mustangs used these bulbs. Don't forget that you need to...

Used hinge for any 1969-70 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint.Replaces Ford part number C9ZZ-6506050-A.

Good used driver side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the passenger side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...

Good used pair of trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the hinges individually. Ford part number C7WY-6542700 and C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars.

Good used passenger side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the driver side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542700.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...