1970 Mercury Cougar

Decal Text: AUTOLITE Regulator D0TF-10316-A NEG

Used until early 1970 on vehicles not equipt with Air Conditioning. Decal Text: AUTOLITE REGULATOR 15V C8AF-10316-A NEG

NOS 41" x 24" Walking Cat nylon banner / flag. These were hung up around dealers back in the sixties and early seventies. We're calling it a banner, but the 2 holes on one side of it indicates it may also be a flag.   NOTE* The reflectiveness of the nylon made it a bit difficult to photograph, just know that the banner is in fact white! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually...

Warning light panel from a 1969 or 1970 Eliminator model Mercury Cougar. This is a modified light panel for the center of the dash. We mill out the raised portion of the bezel where the lights are framed. We mill flat the panel so that the reproduction block off plate can be attached flush with the panel. Eliminator block off plate sold separately. Ford part number C9WY-10C854-B.

Warning light panel from a 1970 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are four visual check items that light up, 'BELTS', 'LOW FUEL', and 'DOOR AJAR', 'LIGHTS'. Specify the color of rubber in the comments or notes. Keep in mind that most of the colors fade or change colors due to UV light and age. Also realize that the rubber trim has shrunken, and may have poor fitment. Plan on dying the rubber trim and re-gluing it to this chrome panel. The...

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

You will need new window gaskets if you plan on changing the headliner. Replaces Ford part #: C9WY-6542084. Installing it yourself? bedding compound is required for a complete seal.Here are some useful tips on installing this seal made by DCMR.From KTL Restorations; Our cure for installing this less than perfect fitting reproduction is to use the longer trim clips (black ones). The clips Ford used were red oxide and the reproduction clips are green. The black clips extend up about 3/32 of an...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

180 pages.

Sold individually, phosphate & Oil (gray-black).

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.